mikuni

VM22 26mm carb and a VM26 26mm carb. What is the difference and which would you use on a modified Predator 212cc?

Every time I find a 22mm I scroll down then it will say it is a 26mm I'm I missing something?

What method do you guys use to clean out your carbs? Let mine sit over winter and won't start without starter fluid

I have a intake for sale that bolts a mikuni 22mm to a clone or predator . It's made to where the carb sets above the motor and faces forward , this manifold is made to bolt on without a top plate to keep it low . From bottom of motor to top of carb is about 14 1/2" s . Also made for a flat...

My son races a outlaw class with 120 snowmobiles. The only rules are no exotic fuels and max 212cc. I just bought a used modified clone with the following done to it. Hemi predator block De-stroked +.17 clone crank +.20 arc billet rod Pvl flywheel Gx200 billet lifters Chromoly push rods...

I have a 212 predator I wanna install a 22mm carb and I can order everything tonight but I have a question. When I put the manifold on how will I get the carb studs out and what kind of bolts do I need to bolt the manifold onto the head. I'm not paying $30 for the manifold from nrracing so I'm...

This is the intake that go kart USA sells for their little bad ass chopper. Fits Honda predator or clone engines to add a Mikuni slid carb. Brand new. Never used. $55 shipped

Anybody have a good used 22 mikuni to be used on a Honda gx160?

Ok so i have a mild built 212cc. Installed a 26mm mikuni with 130 main jet and 12.5 pilot. Ive kind of been going in circles with trying to tune it. What is a good needle setting and mixture screw setting to start with? Ive got it to run decent but it boggs after free rev and sonetimes backfires...

Ok so I had a inyake made for my mikuni and found out engine port on the intake flange bolt holes were too big.so I modified it to work. Hooked it up and found out I had a gas leak so I doubled up the gaskets and that solved it. I got it to idle and free rec good but when I sit on it and give it...

I've been lurking around here a lot in the last few months. I've learned tons while putting together this predator 212 that I am using on a duck hunting boat. What I thought was going to be the last part of the puzzle is driving me insane...the mikuni 22mm knock off. mods on the motor are...

My current build might not gain much going to e85, but my next build I'm going up even higher with the compression so I'd love to have my 22mm mikuni running on e85 already. I'd like to know a good starting point on jet sizes and needle jet placement. I've ran e85 in my drag cars with great...

My setup below. I'm having problems with my 22mm mikuni carb. It only wants to run with the enricher open ("choke" on). It starts on the second pull with the choke on and idles great, when I turn it off it dies, even when warm. I can idle it up with the idle screw for the slide and make it idle...

28mm Mikuni alky/methanol slide carb. Year old bought from nr racing $149. Selling Shipped $110 bucks pay 3% on PayPal.

Is this how it's plumed? I'm I missing something? You don't vent them or over flow lean it over to prime the carb?

Horstman billet intake and 22mm mikuni carb with adjustable main jet and instructions. Came from a member that got it from a member. I never used it. Neither did previous owners. $100 shipped to lower 48

Looking for a intake manifold to mount a mikuni to my honda clone

Im wanting to upgrade my carb on my predator 212 and don't know if its worth it to spend the extra money and get the mikuni carb kit, i keep reading how much of an upgrade the mikuni carb is i just can't decide if its worth spending more than i did on my whole motor, any body have any experience...

I have a predator 212 with 3.308 ARC rod, ARC flywheel, stock dish piston, RTC-6 (stock 27/25mm valve) milled 0.050 off, 1.3 rockers with stock cam, 8 degree key and mikuni 22mm carb. My bike is a Manco with Maxitorque 10T clutch, 43T rear (4.30 gear ratio), stock 16" tires with paddel brake...

So I have a 22mm mikuni carb on the way for my 212. It has 26lb springs flywheel rod isky cam. Any tips for when I get my carb? Can I just built on and start?