issues

Hey my gx200 clone started right up this morning and I let it warm up for a sec then got on and started to go then it died. The choke was off and I pulled it a couple times and wont fire up. I choked it and then it fired up, but wouldnt idle without the choke it would just die. I took out the...

i was riding and my bike all of a sudden started jerking and sputering and then quit. it started fine after that but did again... and again... and again.i dont know much about these engines so could u please help!!!http://www.oldminibikes.com/forum/images/smilies/jg60r9.gif

So for the last few months I have been trying to find a sprocket that would correctly fit my wheel's hub. I measured my sprocket hub OVER and OVER again. It seemed that the holes were each two inches apart, but from my measuring tape it seemed they were just about 1/16 of an smaller. One day, I...

When I ride my Baja 165 down the road it now makes squeaking or metal rubing noises! If I take it apart is this easily replacable? Can I get the bearings anywhere or ? Im not sure really what it is!:shrug:

Check this video out I think they understood it better then than we as a people do now. mVh75ylAUXY

Is there something that I have to do to have more than two pic's in my photos. This is getting me frustrated!!!

Does anyone know where I can get a new one of these? This is from the brake hub end of the brake cable. I need it new and un-crimped. Also How do you put a new lead ball/cylinder on the end of a cable once you get the proper length? Thanks in advance

Now to the back of the bike - See Pics With the wheel centered, the drum brake is about 1" from the LS of the frame, where it needs to mount. From the looks of it, I need to do the following: 1. Cut the "prongs/fork" off the drum brake to make it almost a perfect circle 1a. Grind out part...

I have two DB 30's and thought someone might have expeienced the same thing. We ride the heck out of our bikes in the desert and woods. The kickstand bracket hits alot of the time. We broke the spring attachment arm and now I just have that metal wing (bracket) welded to the bike. I can...

I'm new to the forum and Ive just purchased my first DB30 for my sons (this is the first minibike I had since my Sundowner in the early 70's, what a great bike that was, wish I still had it). I received the bike yesterday and the shipping container was soaked with engine oil. I wiped down the...

My friend has a 09' Blue clone in his kart. It has the governor removed and a header. Sometimes it has trouble starting/idling. As long as he has the gas wide open, it runs like normal. But as soon as he takes his foot off the gas and slows down, it will start to stutter, hunt for idle...

So i got a 5 horse briggs stuffed into the Ding How, but i have a couple of issues. First off, I have no room at all for my foot on the footpeg because the starter shroud sticks out so far, and i also have no room at all to get an air cleaner on it because the frame rail is about 3/4 of an inch...

I have the 97cc DB engine and need to remove the stock clutch. I have removed the bolt and washer from the end of the engine output shaft, but can`t get the clutch to move outward and off. I am sure there is a recommended method to this removal process. How about a little insight from you guys...

i recently picked up a doodlebug in very good shape with a junk motor for 80 bucks, so im taking the 6.5 clone out of my old azusa frame because the doodlebugs bigger tires and better brakes will be better for the trails i ride, anyways, im having trouble getting the chain exactly lined up by...

I have a Rupp Roadster 2 with starting problems. Yesterday I got it out of the garage where it had sat for the last 10 years, changed the oil, cleaned the carb, and put in a new spark plug. After fixing the carb (float needle wasn't attached) and some tinkering around with the jets, I got it...