knock

Ok I did as much searching as possible and all I found was a torque spec. How much do I tighten down the Jam nut on the driven? What should line up correctly in a static position ect? The torque spec I got was 14ft lb. but that was also on a GTC set up... I tightened it up enough to bring the...

I have a knock off tav2 and the center to center measures 6 3/4". The 203589a belt is for 6 5/8" - 6 11/16" and the manco 5959 Is for 6 15/16" - 7". I'm right in the middle of both of these, what should I use?? The driven clutch is centered to the backing plate. Any ideas?

I have a non hemi that has developed some type of knock. Before the knock i had a hard time setting valve lash, but eventually got it. Went out and did a full pass to test it out and came back with a slight knock. took the head and pull start off and turned engine over slowly by hand and it...

Finally got to finishing the engine for the ARCO. I needed to swap the crankcase cover for one that would accommodate the clutch guard bracket, so I pulled it and put on a new gasket and torqued it in place. I lubed the journal before reassembly. I swapped carb and tank for a smaller tank...

Is any one using the Cheap Knock off TAVs on Ebay? If so what are the likes or dislikes? Anyone use one on a Big Block or a 1 inch shaft engine? I assume that Comet is out of business and no Patent Rights to worry about so that's why there are lots of the $100 TAV's online.

Today, I started tearing down my 1970 Roadster for the build-off. After a few days of soaking, the swing arm assembly finally came apart and I was able to get the entire bike stripped down except for the jackshaft. I can't get the roll pin out. I tried using all sorts of different tools to knock...

You guys are in and out of these engines a LOT more than myself. This one came off a HF wheelbarrow air compressor. The symptoms I was told was just "It just quit running." I know about the low oil sensor. I think they ran it low on oil; and never changed it after break in. It is a little older...

Okay, so I got my swap kit from OldMiniBikes warehouse, and I'm gonna go pick up a predator from the local HF. It'll be a hemi model. I'm not gonna go wild with this one yet. I have a header, breather kit, and I'm gonna run a carb that I had on my clone that is on my race cart. mostly stock carb, but...

I have done the unthinkable. Looking at a local on line consignment auction I frequent and they had a Honda Trail 70. Not a lot on it in the way of decals etc and it does not run, but I got it cheap. It is an hour away and I have not looked at it in person, just taken the seller word on a lot...

i recently pulled the motor from my mini for winter since i neddt to replace some parts, paint andfix my engine, not to mention clean the heck out ofit, alot of hard riding :thumbsup:. so heres the deal, it knocks, i mean the valves make a ka- clack sound when turning over by hand and when its...

the 125cc Lifan knock off....Do they really bolt in and go??? is there a better bang for the buck??? thanks

well, the saga continues,i'm gonna ck oil clearance w/plastigauge,have new rod bolts but forgot how to orient the beveled washers. (help again please)

okay, i'm stumped. bought a dupor, flat top piston, installed my used arc rod w/new bearing, fly wheel, 18lb springs,jet,etc. when i spin the engine by hand(without the plug,of course), i have a knock. pulled the head- off-no knock. it appears to be coming from the vacinity of the cam,i think...

okay, i'm stumped. bought a dupor, flat top piston, installed my used arc rod w/new bearing, fly wheel, 18lb springs,jet,etc. when i spin the engine by hand(without the plug,of course), i have a knock. pulled the head- off-no knock. it appears to be coming from the vacinity of the cam,i think...

Hi all, I have an old Manco with a 2004 vintage Tecumseh H40 that knocks under load. The engine has very low hours. The fit between the rod and the crank are tight. The piston fits tightly in the bore. The magneto and flywheel had a lot of surface rust but I buffed them clean as new. The...

so as many of you know, these little doodlebugs aren't ever put into theme builds. so i decided to take it upon myself to build... THE GROUSLE BUG (pics and backstory coming soon)

bonanza 1300 every thing works but motor has a knock p/u only

ok guys i just did my 14cc head swap and i think i can hear a little knock heres the setup so far. Blue HF clone 30* timing uni air filter #90 main jet 14cc head ported and unshrouded valves (New) .010 head gas 1'' pipe i made 3/4 briggs muffler (new) 18lbs valve springs 91pump gas...

Guys how good are the 6hp engines from Harbour Frieght. Considerably cheaper but are they worth it? Thanks

I have a briggs 5hp cast iron bore, It knocks bad at wide open throtel otherwise runs good