sale:

For Sale: N.O.S General Jumbo Jr Tires These are the same sidewall and Tread that are on the Hiawatha Doodle Bugs.The size is 8 x 3.00-4 they fit a 4 inch rim. 8 inches tall.Absolutely Mint,ultra rare! even in used condition and these are mint,as new original's.I will sell these separately,or...

I have a very rare - 99% restored to working condition, vintage, Baldwin Trail Cycle (Tote Gote cousin). These were made in the 1950's and early 1960's. These bikes were manufactured in Twin Falls, Idaho and not many are left. I have installed a new 6 1/2 hp Predator engine, and recovered the...

Selling off the KX125 engine I have for sale. The jug that's on it currently is the later version with the exhaust port facing straight out (1988-whenever of the same vintage). New gaskets all the way around, brand new top end. Cylinder on this one has an iron bore (yay!). Comes with...

For sale,Ruttman New correctly repoped Pac Mule Bars,fresh Chrome,may work for A harrison too.Get them for a great price.$30.00 Pay Pal or Cash on Pickup Shipping,lower 48 $15.00:thumbsup: Dimensions approx 10 inches across the bottom,14 inch rise,31 inch end to end overall width, 7/8 Dia

Hey Fellas, I had these triple tree plates laser cut a while back for some forks I was planning to make but never got around to. They are a perfect match for Taco forks but you can use them for any customs forks as well. Made from 5/32" steel just like the originals. $25/pair plus $6 for...

For Sale Original Lil Indian Brake with 1 inch on center mounting for 68 and later Lil Indian's.New return Spring and new pucks,very clean,no chain rash. Ready for a restored show bike or daily driver!. $175.00 plus $5.00 Shipping Firm! lower 48 States,or local pickup is fine! Paypal,using...

Hello guys. I registered here to see if anybody is looking for a good clutch. I build a motorized bike with a 212cc engine and have 2 new clutches for sale because I needed one with adjustable engagement due my long gear ratio. I am selling: Hilliard Extreme Duty 3/4" Clutch 12T #35...

Hey Fellas, I have a set of Powell forks and handlebars for sale. The forks are working correctly but have some dents and may need a surgery like the one I did here. Handlebars look straight. Looks like someone painted them silver at some point. I'm askin' $125 plus ship. Thanks, Scott

I'm selling my 1971 Rupp Roadster2. It's been fun to own for a while but I need to free up some cash to finish my remodel and take my fam on a vacation this year. It appears to be the original paint, you'll see the light rust on the rear fender, frame, and swing arm in the pics. The tank is...

Hello, For Sale: (2) metal Briggs Tanks ( I think) Solid but have slight rust inside 10.00 ea. plus shipping. (2) Plastic Tec Tanks ( only have one bottom bracket) seen in pic that goes with the right corner fill tank. 15.00 ea. plus shipping (1) Tec HS40 shroud. 15.00 plus shipping...

Rupp digger frame and rear wheel 60.00 mdt frame and front wheel 40.00 broncco tx1 frame, wheels,and tires 110.00 all sold

BUILT THIS AS A BACKUP AND DIDN'T USE IT NEW BUILD RUN IN TIME WITH LOW PRESSURE SPRINGS AND 10 MINUTES ON THE BIKE NEW HONDA BLOCK NEW HONDA CRANK NO GOVERNER VENTED BLOCK AGK STANDARD LENGTH ROD HONDA FLAT TOP PISTON AND RINGS AGK PORTED/MILLED BIG SS VALVE HEAD 14cc .010 GASKET NR 285-0607...

Good motor. Runs good. This does run and idles good. However it does not have an air filter or breather cap. So how you see it is how you get it. Looking to get 50 bucks out of this thing.

Seeling the 6 frames and parts shown in the photo. I was told 4 of the frames are: Keystone Arctic Cat Scat cat Doodle bug At this time I'm looking to sell the entire lot and will not split up. I'm located 10 min north of Allentown, Pa 215-768-4499 $600.00 for everything.

200cc. Electric start. 5spd semi auto. 25" tires. Runs like new. Everything works like it should. Plastic still very shiny and has no cracks. Seat has no tears. $900 1 hr south of Boston.

I have a Rupp C-350 project. It has surface rust on the frame, will need a total sandblast. There is no engine. I have a nice set of original finned wheels with new tires and tubes, a decent rear chrome fender, NOS front fork tubes, new upholstered seat. It is a good starting point for a nice...

I have an early 1960s Skat Kitty we should sell as it's just sitting since I got my CAT eliminators which were my childhood mini bikes.. It is black and has a hand brake lever, non stock foot pegs and is missing the clutch cover. Nice low serial number and it looks like it never had much use...

This is a super rare Kawasaki KLT three wheeler cover. It has never been removed from the box until pics. Original box and storage bag included. The cartoon logo appears to be a 1980-82 KLT200. $270 shipped.

This is a NOS TriSport travel/storage cover never removed from the original box until pic. $99 shipped.

Anyone out there need any double row #35 chain? I have a few rolls of it. By the foot or buy it all... $15 for 10 feet plus shipping. I have no master links for it. Please email to oscarhedstrom at yahoo.com in Massachusetts THANKS...