carburetor

I'm fairly certain this came off a little 3.5 Tec, but I would like to make sure and have a few questions. I am thinking about putting this up for sale and would like to make sure I don't mis-advertise it. It has lots of numbers on it stamped in, and a drop down style intake. Any sure bets on...

I need to know what the flange size is on a GX160 Carburetor,I have a 5hp Subaru robin that needs a carb and i cant find one the flange size i need for the robin is 42mm i was thinking of getting GX 160 Carburetor (Thai Z0T) Form NR racing but i don't know if it well fit. if not What carb will...

I need to know what the flange size is on a GX160 Carburetor,I have a 5hp Subaru robin that needs a carb and i cant find one the flange size i need for the robin is 42mm i was thinking of getting GX 160 Carburetor (Thai Z0T) Form NR racing but i don't know if it well fit if not What carb will...

Hi, I recently purchased a bird duck minibike off ebay. It has a tecumseh h30 motor on it, but there is no carb included :( I am needing to find a good working carb for this without breaking the bank. The guy selling the bike said that the correct carb for the motor was a 648400B carb. When...

Ordered new from NR Racing but found out all my original carb needed was a gasket. Will fit all GX200 clone or Honda engines. Paid $40, will take $25 including shipping to lower 48.

I am putting an OEM Honda carburetor on my clone at the recommendation of Russell at NR Racing (my clone carb had issues). I just received the new carb and noticed that the mixture screw is different from the clone (pop off the black plastic cap for access to the screw). The Honda carb does...

Hey guy's I am looking for a little direction. I bought this mini bike and I think some of the carb linkage is MIA. I followed a couple of you guy's advise and it starts with a little messing around with the choke. I cleaned out the carb and tank. I cleaned out the little screen on the...

Does anyone have a link to a good description of how exactly a carburetor works and maybe some troubleshooting guides to get mine set right. I have a 4HP Briggs that I can get running with starting fluid and once i hooked my gas line up it still needs fluid. I also need some help setting up my...

Tillotson HL 329C 641. 1 inch bore where carb attaches to manifold. Very good condition. Set up for gasoline. Came off of a US Motor Power 820 engine.United States Motor Power, Inc. $30.00 shipped.

I'm needing a carb throttle/butterfly shaft for a gx200 or clone. The plastic piece on the top that hooks to the throttle linkage is broke on one of my carbs. I'll buy a whole parts carb of just a shaft if that's all you have. Thanks

My 6.5 clone carburetor is leaking at the on/off valve. If off, it doesn't leak, if on and with the motor running it doesn't leak but if I shut the motor down an don't turn the gas off it leaks. Ive taken the two screws off that hold it on and the rubber four holed gasket looks fine, as does...

Would a 24mm round slide carb be too much for a H35 tecumseh?

Does anyone know if you can buy the fiber washers that go on the carburetor float bowl drain plug and bottom bolt without buying the whole carburetor gasket set? After a few times changing jets, they begin to disentigrate/leak. I've checked hardware stoes an none of them have any that fit.

im looking at this carb but i dont understand what "blueprinted" means.

Just got a '74 Yami TY80 yesterday. Got it for a song, aside from having to drive 3 and a half hours to get it! Pretty decent condition, needs some stuff but it will be a fun little winter project. So the problem I'm having is that it will only run with the choke full on. Is this an indication...

I would like to buy a replacement carburetor for my 5hp Tecumseh. I've taken it apart many times, but still can't get it to idle. Can anyone recommend a vendor? My motor came came off a snow blower. Is there any reason I shouldn't buy the same carb? (I ride in summer)

I need a carburetor with the elbow bend for a mini bike project. The existing carb is the syphon feed, i need the gravity feed. The current syphon set up does not allow for proper clearance. Keny 609-694-4171 or kenykop@yahoo.com. If I cant get the carb the engine will be for sale...

How many of you guys remove the Swirl from your B&S carbs? I've been tinkering with a clean, little 3.5HP B&S I/C for the DB-30 swap. I plan to replace the diaphragm gasket set on the side of the carb, before I button everything up. I was reading some information on how to 'Blueprint' a...

New Carb, never used $25 plus shipping I have some 8mm spiro core plug wires, great for replacing the crappy stiff high resitance stock wires... these are silicone jacket, spriro core, 8mm (2) pink (1) yellow (1) green $7ea plus mailing fee coil not for sale, just for reference to...

i need a carburetor or just the air cleaner gasket for a baja gxh50 clone. anyone know where i could get either part? maybe off someones old 2.8 after a 6.5 clone swap??? willing to pay 35$ for a carb