mamba

predator 212cc rtc-6 cylinder head with 27mm intake 25mm exhaust valves stock automotive style retainers 26lb valve springs with .060 shims on intake and exhaust sides stock rods stock rockers billet rod +.020" hemi flat top piston .010" head gasket ngk spark plug billet flywheel 32...

wtb black mamba cam for non-hemi predator.. no rush.. for a budget build

For sale: Black Mamba Sr. Cam. Approximately 1 hour run time since brand new. $50 shipped. This is for the non hemi predator.

1st post. Have done lots of reading here. I'm looking to build a high torque low RPM motor for a boat mud motor. I have a stock non-hemi on the boat right now and it bogs pretty bad and will only run 2000-2300 rpm with a full load. I need more torque to get it up on plane so the motor can...

I have a black mamba Jr that is like new, only used for 30minutes. I'm interested in the black mamba Sr or another high lift high rpm cam .even trade each pay their own shipping.

when installing the black mamba cam do I need to get new valve springs right away, or can I wait a little while before I get them? will the engine run correctly without them?

I have a predator 212 with a black mamba and am looking for a clutch that is better suited for the motor. The motor is very fast on the top end but seems to have less low end torque than my predator that had a flat top , pipe and intake. Right now I have the max torque clutch with the 3300...

I was wanting to know some real dyno numbers with engines running black mamba cams. I'm needing to know how much I need my clutch to stall. I'd like to at least hear what rpm peak torque was at. I'm running a black mamba cam in a predator with a 18cc Honda head milled .050, SS valves, ported...

Can you tell a difference in idle and sound with this cam just curious thanks

Is this a good cam for torque and mid range power? Also should I upgrade to different carb? Does it sound good? Just curious because I am wanting to buy one seem like a lot of people like these cams. Thanks

Why is everyone out of black mamba and black mamba jr. cams? Ive heard such good things about them, I wanna try one.... Were they discontinued? If so, what is a similar performing cam to go with?

Got a new Predator, and decided to tear it apart. Its down to the bare block, plugged all of the holes from the governor (2) and oil sensor. Just got a, Isky Black Mamba cam and springs today. Installed the new springs. Waiting on the billet rod, flywheel, Mikuni carb, manifold, jets, and...

where do you get the black mamba sr cam nobody seems to have them in stock and whats about the dyno cam is it a good choice

Picked up this new carb to good to pass up Can anyone tell me a little about it.a few guys in my area are running them with good results .I've been running a 22mm roundslide mikuni knockoff on my predator 212 runs good mods are Arc rod &flywheel 8°advaced key Black mamba sir 18cchead 27/25...

planning on a cam and valve train upgrade haven't decided on whether to buy the big valves and install them or buy a head that's already done but need to decide what cam would be best for dragging leaning toward black mamba

im starting my little string of winter modification and was curious on my current cam selection. Heres what i have. Hemi Predator- billet flywheel billet rod Robertson loop header, and straight under seat header arc .625 carb and intake 4* advance key 26lb valve springs Im about to...

I,ve been following for a year on here and usually find answers I need. Now however I'm stumped and in need of advise. Engine: Predator 212 w/ Billet rod Black mamba Jr cam 14cc head w/ stainless stock valves 26lb springs 1:3 rockers Cone intake Robertsons H pipe Fuel pump Issues...

I have a low run time Black Mamba cam for sale or trade. I will trade for another cam like a Black Mamba Jr. or a Dyno CM cam. Don't get me wrong I love this cam I have 2 others just want something different. This cam is for Honda GX200, clones and Hemi style Predators. Asking $50 shipped to...

Looking for a black mamba sr cam for old style 212 website says not available

Hey guys ive been running a mod 2 cheater cam for the last year in a little drag bike im running. i only do 100ft drags and its been going good but ive been reading here that the jr mamba is better. i ordered the mamba and have it in hand but i just raced a mamba and i killed it:scooter:. but...