axle

I picked this up for $175. It's complete and runs great with the original 3.5 tecumseh. There is about 1/8 inch of side to side play in each side of the rear axle. Is that normal or should I tighten the axle bolt to close the gap? Not sure if my picture worked. Thanks.

What do you guys use for axle grease on your mini's? Right now I've just put everything together on my builds temporarily just to see how it all fits and looks but I'll need to reinstall the wheels and greese up the axles when I'm ready for action here. What do you guys recommend?

1970 Roadster, Enduro, Scrambler. Front brake assembly. Backing plate, hub, axle and spacers. Free Shipping to lower 48 states. $65.00 Roadster, Enduro, Scrambler. Rear Brake assembly, sprocket, axle and spacers. Free shipping to lower 48 states. $75.00

Pair of pretty nice Go-Power wheels.5 inch,no denting or scuffing,the rear has a little pitting on the inside ridge.Rear has a sprocket.I have NOT tried to take these apart,so the allen head screws are not stripped or rounded out.The tires look to be nearly perfect,they are General Jumbo...

Made up some Flexo parts today. Gerry shared a photo of the engine plate with all the measurements I needed and Karen was nice enough to mail me a rubbing of the jackshaft and axle tabs. So here's a much deserved thank you to them.

Hi everyone, Could use some assistance in tracking down a thread I found that contained an alternate way of connecting a wheel axle to a new frame tube end by using an eye bolt as pictured below. If anyone can recall what thread it was in or possibly where a guy might buy these would be very...

Hey Everyone, I am trying to pick up my 3rd db30 this week. I am considering converting this one to a trike. I saw a few other threads and will be watching those much closer if I do go this route. 1st off I have a 38" axle - is this too wide, too short, or just about right? Is there a...

Has anybody used them before ??? Looks like you could use a #35 60 tooth blank sprocket and drill it to fit. Not sure about axle size though. Would a 5/8" axle fit ???

Right guys Iv been working on a trailer for my Goliath tank. I figured why spend 300$ on a harbor freight trailer when all I really want is the axle and springs. So I scrouged up everything I need for it. I even managed to make an axle so all I had to buy was the springs. I had a long length of...

Hey so since I had to saw my Black Beauty axle up to ge the brake off I'll need to order a new one. Hopefully OldMiniBikes has these? I don't have the axle pieces anymore so I'll need help on it's size. I might have two small peices so measure for width but not sure of the length. May have been 9...

Ok so I touched on this in my project thread but I know that isn't the place for questions. I bought a 12" rear wheel on ebay to replace the 10" in. the bike came with and it came with axle, bearings and spacers. Plus those oblong washer looking things with the tabs sticking out. When I...

i seen this go kart on the web a bunch. but there no info on it. i want to build it this summer. but the rear axle and sprocket gots me stumped. please help

Hello, I am new to this forum. My wife acquired a trisport frame that I have been working on this fall and hopefully I will have it running by spring. While removing the seized in front axle, I destroyed it. What material should I use for the new front axle? I can get shafting from McMaster...

Looking for parts to build a trike. I have the front fork and some steel but I'm missing A LOT! I would like to have a live axle. A complete axle with wheels, sprocket, hubs, etc would be awesome I need a brake setup I need a front wheel for a mini bike ( my fork is from a mini bike...

What all would I need to put some 8" gokart slicks on a live axle? really confused with what parts I need.

I am rebuilding an old Manco Express go kart for my grandson. I need to reposition the live axle drive sprocket because I am installing a Harbor Freight 212cc engine. I am not sure how to loosen it on the axle. I have removed the four bolts but it won't budge. I don't see any set screws. I am...

I was riding my Baja Warrior, MB200, whatever you want to call it and the axle nut came off. The axle bent and I ordered another. But of course the axle did not come with a nut.. I have searched high and low for this thing. Online, Home Depot, Lowes, ect with no avail. Its a chinese bike so I am...

38"long 1" diff axle. Very good condition. No sprocket. $80+shipping

Nobody local had steel sleeves and I didnt think bronze sleeves would hold up well so I went this route . Is this ok or not really the right way to do this? I did mark the axle with the set screws ,then drill the axles for the set screw and stake the collars so the set screw will not back out ...

On a live axle setup with threaded ends on the axle and keyed wheels, what keeps the wheel from sliding in toward the bearing blocks? I'm assuming you need to put a locking collar on the axle just inside the wheel but can't really find any reference to show me that. I'm putting together a...