bolt

Hey guys I am going crazy over here trying to figure out what size these bolt holes are on the side cover to mount my back plate on this 212 predator. from what i have narrowed down its not 6mm nor any of the 2 8mm thread patterns. now common sense would say that it has to be 7mm but trying the...

Anybody know, with certainty, what the rod bolt torque (arc rod) is for the 5hp flathead ? Thanks, Pete

Ok, here's a noo-be question. (Yes, I'm sure it's out there in cyberworld somewhere, but I really need to know now...) It's been a few years since I've dug into these little motors (like 40 years?) and when I took the head off to see how bad the guts were I wasn't paying close attention the...

need to figure out what size the input shaft bolt is c

Just installed a new Hilliard clutch to my 6.5. It is only held on by a single bolt thru the end of the crankshaft and a lock washer. Problem is....I haven't figured out how to tighten the bolt enough as the center of the clutch starts to spin. How do you hold that sucker still?:crying:

my buddy has a HS50 and manifold for a tecumseh 5hp that he doesnt need and i cld get for a good price. Will it bolt up?

So If a drain bolt is stripped on one of these things could I use a hand drill and drill the hole a little bigger and tap it? What's the best way to fix it? Greg

i went to Tractor supply today .they sell grade 5 bolts for $3.69 a pound. the grade 8 are less than $5.00 a pound. :thefinger: to OLd Depot getting a buck for a 5/16 bolt . Tractor has P B BLASTER $3.50 a can

what size self tapping bolt/screw will fit in the govenor arm hole and not break it? i used the search on screws and boltsand i got torque and linkage ideas . i hate to buy 2-3 packs at the depot, they want you to buy plastic bags full. i need 1. i have instaled the flywheel ,rod, rings flat...

Anyone know the bolt pattern that is on Azuza 10" wheels? I am working on a billet disc brake setup and need to know. I know it is a 4 bolt pattern, though.

I need the bolt size to mount the clutch guard mounting bracket(OldMiniBikes bracket) to the 6.5 clone engine. I've searched. Thanks.

How many bolt pattern sizes are there for the standard 2.5,5,10hp engines? Would a HF 6.5 clone share the same bolt pattern as the 2.8 in a Baja dirt bug and be a relatively easy swap?

Hi, I was riding and the bolt that holds the clutch on fell out somehow. I have looked everywhere for this bolt that holds the clutch on. My engine is a tecumseh h40 55806a could someone please send me a link where i can buy the bolt. THANK YOU!!!

I was cleaning out my photobucket and came across some pics of a old how to thread I did for the guy on a budget. I originally came up with idea when I was reading a thread about some unhappy results with a man painting some of his hardware black, So I went and threw this simple process...

i Found out today when you put in a clutch shaft bolt use a BIGGER washer than the clutch hole.. DUH. my arm and leg hurt now.

I tried taking off the bolt but it was too hard. I even put vice grips on the other side of the shaft i put alot of pressure and the vice grip even slipped cutting the metal off the other side of the crankshaft? I am trying to change crankshafts and its my first time. I need tips and help taking...

All carbs listed have just been completely taken apart, cleaned, rebuilt, fulcrum arm set, pop off set, all new stainless allen head bolts/screws, and all come with filter adapter with filled in and blended screw holes. All very nice carbs, ready to bolt on and run. They have had NO fuel through...

What size is the crank bolt that holds the clutch on :shrug:

so i go my OldMiniBikes clutch guard and was wondering whats the bolts i need to mount it on ?? i think they are m8 by 1.25 right ?

My brother pointed out to me that mjy front fork bolt was too tight, now tehres a arc in the metal from bar to bar cuz of it, ( this was pre assemble ) now im trying to put an extra washer in it but since the metal is wrarped i get get teh washers tpo slide in, its so BS.