cap

I need a gas cap for a Bronco Renagade TX-10

Does the arc billet oil cap threaded 3/4" x 10 fit the predator 212cc non hemi?

Hello, we are in need of a spark plug cap w/ the spring inside that attaches to the spark plug ?? These are made of brass and screw into the main cap.. All the Indian & Italjet mini's used the same parts and pieces. I know i can gerry rig it pretty easily, but we would like to find the...

nos Briggs gas cap/gauges, approx 3 1/2" tall, will fit Tec plastic tanks as well but goes on a little tighter.. $5 plus ship

I lost my lash cap on the exhaust valve while taking head apart, could I get a lash cap from auto zone or napa or somewhere? Do I even need it? Could I run the motor for a little bit before I get one thanks

It's not a perfect match. The top is a little wider. Every thing else is the same size. $30 shipped paypal only add three percent or send as a gift.

so i bought an aluminum tank and mounting brackets for a predator. the rear mounting bracket is a poor design, i feel. get in the way of the throttle linkage mount. anyway, the cap came with no gasket. i didn't even really think about it until i couldn't figure out why gas was leaking...

Can anyone tell me how to get this old rubber out of this gas cap? a It's old and dry and useless and gas leaks out of the tank. It doesn't look to me like the rubber goes around the center metal section but rather most of it seems under the metal. So I assume I have to turn this metal piece...

couple of years ago I had made a vented guage gas cap similar to the original ones Bonanza used on the fiberglass tanks. This style cap is NLA, other styles that come close can be found but not with a vent you can close usually. The idea to modify the one I had came from the fact that the...

I've come up empty so far ( not giving up ) on locating a Roper gas cap , does anyone know of an alternate cap that will work and look close to correct ? Thanks :thumbsup:

I am currently redoing an HS50 to sell and am kinda wanting to do it in white. Was going to do silver or black but the last few have been those colors so I wanna switch it up. I need a clean plastic one, side fill-I have the same in black (and a nice black center fill too if you needed that...

The PO left it sit out side without the air filter cover. There is rust in that tray that sits under the carb but every thing else looks nice but the gas cap is broke. PM with any questions, Nate $10 plus shipping

The motor I was using had burnt rings. My buddy gave me a motor that runs great, but the pto was broken off. I decided to take the crankshaft from the smoking engine and put it in the good one. While doing this I mixed up the connecting rod end caps. Does anyone see this as being an issue? Is...

The Speedway tank is clean inside but has a small hole on top in front of the gas cap & can be fixed easy. $35 The other tank is ?? $15 Both tanks plus shipping

Hey Guys, I'm at a lost with this motor. Could really use some help. I have a brand new 212, header, air filter kit, and 037 jet, and 140 e tube installed. It starts fine but runs at a high idle and when i give it a little throttle it dies. I've try cleaning the carb, using the 036 jet. nothing...

My gas caps on on my mini bikes tend to "weep" small amounts of fuel if going over bumps or after an aggressive ride. I assume this has to do with old seals in the cap and venting or lack there of.... Aside from cap replacement, does anyone have any good fixes or repairs they've done to keep...

I have been working on a 3hp side popper for my Manco mini and today I came to the realization that the fuel tank is mounted on the back of the engine and will be impossible to refuel. I have a junk 5hp with the tank on the front of the engine the problem is the fill cap interferes with the tank...

I am looking for an old broken top arctic cat mini bike gas cap with gauge. The gauge has " arctic " on it with a red needle.

Started on the black widow. Everything was good until I opened the carb. Need the top part of the carb where the filter is located. The filter slides over the threads and a cap holds everything in place. The threads are gone ugh. Rest of the carb looked ok. Thanks dave

Anyone know a gas cap that will fit the OEM tank?