carb

Hi, will the exhaust being this close to the carb do anything bad? Tom

Need parts #10,11, 13, 14 for sure! Anyone know of a contact? 818 438 9889 Thanks

saw some 19mm chinese mikuni clones for sale has anyone tried one of these on a 5hp flathead?

Got both of my H60s running today (subjects of an earlier thread). Both have brand new H60 knock-off carbs. After running the solid state H60 back about a month and a half ago, I had way too much fuel even with both circuit screws barely open. So, I reset the floats on both carbs to be a bit...

Hey, will a 270 carburetor fit on the 390 adapter for the gx200 clones? That question came up over on the Mud Motor Kit forums. As we were discussing modifieds, someone I wondered if it'd fit. I wonder if its a better deal than a .670 stock appearing carburetor? It seems once you buy the adapter...

What size carb do you guys recommend? I might order a carb on Monday for my build. Big bore 208cc clone, CL1 high torque cam, stock ratio rocker, 18cc head with 26mm intake vavle, will have about 9.0+ compression, GXV 160 flywheel with probably a +4* key and a billet rod. Its only a 5,500 RPM+...

So many times i've searched for this to no avail but does anyone know if there is a list out there of replacement carb part numbers AND the carb part numbers they replace? Sometimes you come across an nos service carb and searching for what it could be used for is a real journey

I just picked up a Murray Track 2 built 2001 or so. It looks like new. The person I got it from said he and his 13 year old son had rebuilt the carb recently because it had been sitting. It would only idle for me with the idle turned up and was surging a bit as accelerating and at top rpm till...

DELL ORTO SHB 19.19B Carb with Air cleaner off of a Indian mini-cycle $75.00 Shipped USPS 3 Day PayPal

Tecumseh Lauson diaphragm Carb. Came off a 3 hp. It is untested. part# 52 1c9 Everything looks good and moves freely, should just need a cleaning and diaphragm. $50 shipped. Paypal as friend or add 3%.

looking for a UA19S carb in any condition. call 240-299-0644 or email me at csmolen@advantagestarmortgage.com

Anybody got a 2HP tecumseh carb? It uses the airvane gov, my housing is cracked where it mounts and in 2 pieces or thoughts on welding. This came off a 50's sears engine and also looking for a head gasket, it is seeping alittle. Thanks Ron

Looking for a Dellorto UA19S carb in any condition. contact me at csmolen@advantagestarmortgage.com or 240-299-0644

I want to buy a carb kit for my HM80 so that I have it on hand when/if I need it. Where is the best place to find a good quality kit? I just don't want to buy a cheap kit that the rubber will be hard or falling apart in no time. I would prefer a factory Tecumseh kit. Do they still make them...

I am in need of a stock low speed/idle jet for a predator SP 60363 carb.

Question to the experts. During disassembly of the carb for clean and rebuild, I removed the spiral metal pc to get at the throttle plate screw. Any reason I have to put it back in? I am thinking I can leave it out. Pretty much destroyed it getting it out anyways. Thanks in advance Joe51

So I got the CnC Bored Box Stock Carb from OldMiniBikes along with a filter kit and a few other items for my non-hemi Predator 212. After mounting the new carb, I noticed the throttle rod, while in a 'resting' position, is pulling the carb wide open: Then I realized the original stock...

I have an old Lauson/tec engine that I'm guessing is around 4hp (can't find any ID number) I can't get the carb to prime, I've taken is apart and cleaned but no help. Does anyone have any knowledge on these where I can get parts or a new carb? thanks Guys

Can someone confirm my thoughts on this before I go through the R&R again...... I think I have the linkage is in the wrong hole. It doesn't have a good - full return. I think it should be in the hole closer to the intake flange.

Carb