honda clone

This started happening randomly, initially it would kickback 2-4 times before it would eventually turn over and start running, but it ran rough and hot, and started dieseling when shut down However, after giving it a shim head gasket to bump up compression (because I planned on running it on...

I have a non-hemi predator 212 and the crankshaft broke to the point where i can’t put my torque converter on. I’m trying to find a replacement part for it but all I can find specifically for predators are hemi cranks. I don’t know if those are compatible or not. I also found a tillotson...

Hey guys, I recently rebuilt my Hisun 196cc motor and when I run the engine it idles roughly. Here's some specs 18 LB valve springs PVL Aluminum flywheel with 31 degrees BTDC Billet con rod governor removal BSP-2 cam Everything else stock The engine seems to run fine at higher RPM but at idle...

Hello guys. I have a 6.5hp Honda clone from a "Baja Warrior" bike. The oil is full of gasoline, causing it to misfire, and not idle properly. I have checked the float bowl in the carburetor to make sure that the needle for the valve is seated properly. Nothing seems to be wrong with the Floater...

I have some questions I am hoping to get advise on. I did some searching and didn't find anything useful. I just bought a Coleman CT200u. It was used so little the front tire still has the rubber hairs on it. It is a two years old and I am the third owner. The first owner never put oil or gas...

Hey guys, I'm building a Predator 212 for a minibike. I'm going to be running 14cc heads, flat top piston with .020" lower compression height, and a billet rod that's .020" longer to account for the lowered compression height. I plan on running 1.3:1 ratio rocker arms and I was wondering what...

Hello, I have a 136cc LCT engine. Is this engine a Honda clone? Thanks!!

If a small 212c or 125 can run a turbo a 420cc should be able to run one right?. I have a design for the placement but was still wondering about the size I would need.(its a power fist clone from Princess Auto)

Hello, i got a a 7hp honda clone engine all stock, and i was wondering if i were to put a cam in it, would i need to replace any thing else in the engine, the cam i want to put in it would be the. DJ-1104 Cam, Dyno F275 Clone/GX200 DJ-1104 Cam, Dyno F275 Clone/GX200

A few days ago I bought a 6.5hp Powerfist (Honda clone) engine off of kijiji for $50 that I have intentions on putting on my doodle bug. Seller said that it came off a rototiller and ran a bit rough. So I figured I would buy it cheap and get it running right. I brought it home and it...

I took my bike to the shop and they said I need a new carburetor and I remember seeing my friend with a dirt bike carburetor on his engine but don't know what kinds of engine he has. So what kind can fit on a Honda 5.5 clone?

Hello, For sale is my Tecumseh 6HP Engine. This is Tecumseh's OHV Power Sport line of engines. This engine was used on my red Doodlebug Mini-Bike. It has a primer bulb carb and aftermarket air filter installed. A fuel shut-off valve was added. The engine runs reasonably well. It is ready to go...

Baja Doodlebug seat here. It is in good shape with no tears or rips. However, there is some paint on the seat. The mounting holes are in good condition and not bunged. $30 shipped USPS Priority Mail I'm located in Duarte, CA Thanks for looking!

Hello all, I just picked up my 6.5 HP H.F. engine for about $100 including the 1 year warranty. I recommend you guys hurry to get this great deal since they're discontinuing them! 6.5 HP Gas Engine - Horizontal Shaft, OHV Now I found this guy on craiglist selling these "Brand New" H.F...

I bought a go kart with a 6.5hp Honda clone motor is was almost brand new motor i was riding it around my back yard(which was a little bumpy) when the motor just shut down. I got off and tried to pull start it and it wouldnt start. I have replaced all oil thinking it could have been a low oil...

I see that they are sold in 48" 53" and 60" lengths? Which one should I use for an azusa frame with a clone engine? I've noticed that some people set up the cable coming from the back, between the air intake and the exhaust. This would require a longer cable I assume. And others set up...

I tried putting in animated .Gif from google images and they don't work on here. It's just the picture not the animation...The horse <--- should be running right now.

i have a gx100 and a honda 6.5 clone. what parts from the clone will fit the gx160. ive read that the carb will fit straight on but what else could i use from it? what would be better for the gx160 just trying to get it running.

Were is a good place to buy a stock Honda GX200 Clone?? I need it at the lowest price possible and i need all of the available upgrade to fit it. Im not a pro with this stuff but i know that my stock db-30 needs more power. Any help would be greatly appreciated. Thanks!!!