This is like the same set up Rupps used but it's asymmetrical instead of symmetrical.
Basically it's like a 30 series instead of 20 series. This set up came from a fox thunder bolt. Driver was taking apart and cleaned up so it functions properly. Driven has good spring back. Comes with clutch...
For Sale,I am selling,my last NOS,Mint Fairbanks Morse Two Speed Transmission Clutch.I re zinc plated it fresh,as the original plating was a bit scaly,absolutely NO rust though,never been mounted on a bike.This is a rare find item to help complete the Mini matic 2 speed setup...Asking $150.00...
A Very Nice Fairbanks Morse Kickstarter for use on Tecumsehs. All original parts. Rubber is nice and soft.
$225 SHIPPED !!! Paypal strongly preferred.
Thanks in advance :thumbsup::thumbsup:
This likely wouldn't be too practical on a minibike, but perhaps may be of interest on a go-kart project. Electric starter motor to bolt to the front of a blowerhousing; not sure as to whether it's a universal design, as there's no instructions in the box, but this starter motor utilizes a...
I picked this kickstarter up last week for a great price, but the pawl on the back is broken/missing parts. Where can I find replacements or is there someone that makes them?
And doesn't this need the cub to work correctly? Anyone know where to find one of those?
Picked up this one today and its got the Fairbanks Morse clutch on it. Should be able to get it going pretty quick as the compression is very sweet sounding. Its not a Rupp clutch so what bikes were using these clutches apart from them? To use it do you need a matching FM driven system?
Hello too all,Am selling this kickstarter for parts or rebuild for 110 bucks shipped to you.It is broken.Good for a bike that is a shelf queen.If interested just reply and i will get back to you.I am only accepting a money order from the post office or cash on local pick up in levittown n,y...
Any good ideas for getting the backplate off the shaft without cracking it? I've had the motor on its side for abt two weeks with PB Blaster soaking inside. Went to hook up a puller and one side is too close to the motor to get the hook of one of the pullers arms under it. So i tried to pry it...
I have a brand new Fairbanks Morse pull starter. This will fit Some Tecumseh's, Kohlers, and West Bend engines. This is in a Kohler box, but FB made these for Kohler. Labeled FB on inside. This is NOS and has some shelf wear. Cheaper on OldMiniBikes than eBay at $110.00 shipped. PM me if interested
Looking for the correct starter cup and screen to use with the old fairbanks recoil assy's on the early west bends. Even a part number or good photo of the correct one they used would be helpful so I can hunt one down on ebay.
one for this style recoil:
thank you for any help!!!!
I actually just need the inner flange if anyone has one. The one on my Roadster is worn all the way through the face.
I'm not in a hurry, but I'll need it soon.
I have for sale 2 60's NOS Fairbanks Morse drive Clutches that were used on Lil Indian's model 700 and most of the bikes in the Grand Series They fit 3/4 shaft engines,one is a 10 tooth,the other 11 tooth,both are unused mint condition.These were also used on many other vintage minibikes from...
I have a Fairbanks Morse 2 speed clutch that needs springs.
I need one for each side because they are missing. I was thinking that someone may have a worn or damaged one for parts.
Thanks,
Loren
65$ delivered to you lower 48 address.
Will take a couple days to get it out with the holidays and I need to find a box.
5/8" hole
No shaft, in picture months ago but now gone.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.