pushrods

Right now I'm building a predator 212cc and the engine is a Hemi. Aside from the necessary flywheel, carb, exhaust mods... It will have the original head, 1.2 ratio roller rockers, original valves, 26 lb springs, a lift for the valve cover, a mod 2 Dyno cam, and a flat top piston. My issue is...

Just had my Hemi 212 head milled .055, running a +.020 rod with zero deck height and a .027 multilayer gasket. I want to know whats the correct piston to valve clearance...also do i need shorter pushrods to keep proper geometry. Thanks in advance for all input

Just had my Hemi 212 head milled .055, running a +.020 rod with zero deck height and a .027 multilayer gasket. I want to know whats the correct piston to valve clearance...also do i need shorter pushrods to keep proper geometry

Ok guys, I've done a search but I really think I suck at the proper search terms so bear with me. Like the title said, I'm doing my first Hemi build. So far I've gotten all the gaskets I need, side cover, .010 and stock head gasket, and various others. Got an ARC +.020 length billet rod, and...

When I tighten my rocker arms down to .002 or even 0 cold lash the pushrods are super loose on the other end. Are my pushrods too short, or is there something else I need to do? I have a predator with a gx160 head, .016 head gasket, black mamba cam, 26 lb springs, lash caps, burris guide plate...

In the process of modding up at Predator, just ordered a bunch of parts. Got the motor completely apart, governor out, oil sensor out and flywheel off, head off - all the way down to bare block. Heres the plan: ARC Billet Rod ARC Flywheel BP2 Grind Dyno Cam 18cc Milled Clone Head (going...

If you mill your head .030 to .080 would also want to shorten your pushrods the same amount to keep the valve train geometry in check. Or is this really a big deal cause you can adjust lash to correct the amount removed from head surface. just a thought i had . Anyone know or comment ?

hi guys whats the hot setup for cam upgrade black mamba sounds popular but i seen Isky alot too got a hemi motor but havent pulled the head(or even the spark plug lol)so not sure if i have a dished piston(should i change to a flattop piston) where is the best source for all these parts cam...

Finally picked up some chromoly pushrods and guide plate. iv been running the stamped 1.3 rockers and black mamba sr on stock pushrods for awhile. wen I installed the guide plate it raised up the rockers should I get longer pushrods or did I install it wrong lol or should I get the rs guide...

I set my lash on my valves after I switched my head to a 18cc head and the lash keeps coming undone and the push rods fall out why is it doing this ive never had this happen before, I put a billet guide plate on under the rocker studs,

Comp GP4673 1/4" stock length pushrods for 305 Briggs, never used.. $20 shipped

New stock length 5/16 chromolly pushrods.... paid $16 each plus shipping, sell for $25 shipped....

OldMiniBikes sells stainless steel pushrods for the gx 200, my question is will they fit a predator and will they be stronger and an upgrade from stock.

So, I have all my parts for my clone to include The s2 adjustable pushrods .065 milled head and ported (gx 160 head on 200 clone block) 1.3 roller rockers .290 lift cam from agk 28.5 intake valve 26 exhaust Flat top piston Stock length billet rod 26# springs 26mm mikuni carb Norma cheetah...

Just curious on whether 5.070" moly pushrods with billet lifters will give me problems since I had the head milled .065"? Don't have items infront of me wanted some insight, thanks.

Hey guys its been a while since i posted up hear. Ive been at school for to long. My dads been trying to get me to fix his generator. At first it looked like a broken push rod so i replaced it with a new one. A few days later he said it stopped working so i took the valve cover off and the...

Twice the strength and half the weight. Puts chrome-moly to shame. Ive got enough rod for one set. Sell or trade. You give me the specs and I'll get to turning this titanium...:thumbsup: $40.00 for a pair seems fair if theres a high enough demand i'll get some more titanium stock. What about...

What would cause a bent pushrod?:censure: