sprocket

Are there any rear sprockets out there that are #35 chain and smaller than 60 tooth? all im seeing is 41 chain.

I know I've seen it done here but can't locate the threads. I need to reconfigure a Model 30 TC so that the driven sprocket is on the inboard side of the backplate. Short of obtaining a new 5/8 shaft, what else is involved?

I have a 71 Fox Banshee that came with a welded on rear sprocket to the rim. The tire size it came with is a 4.10x3.50-6 I cannot make left turns without the chain dragging on the ground and popping off Would it be best to change the tire to a taller one? I dont have much room; I'm not sure...

Looking for a set of 6" wheels, 5/8" axel size with a #41 sprocket. Looking for something with decent tires.

OldMiniBikes warehouse is out of stock on sprocket adapters and I need one. Any idea where else to get one. Also any advice on throttle cable replacements?

Need a complete 5" El Tigre rear wheel and sprocket. A kick stand will be a plus! Will consider 5" aluminum alternatives (a matched set) Thanks!

I'm looking for a sensation stroker and spacers and a sensation chopper seat thanks eddie

I'm looking for a sprocket for my Arco bushwacker. Heres a pic of the back rim. Holes are about 2" 9/16 apart. Let me know if you can help. Thx

In need of a 72 tooth rear sprocket for a 68 tt500. It can be used, just has to have teeth in good condition.

Predator gas tank 2 Predator stock exhaust 2 Predator stock air filter Foot pegs 2 brake cables Clutch guard 2 misc sprockets

Hello. The rear rim on my 1971 sears roper is bad. Turns out that the sprocket is badly bent. Can anyone suggest where i can get a new rim and a bolt on sprocket? The sprocket on the rim now is welded on Dimensions are as follows Rim diameter 6" Rim width 3.5" Sprocket diameter is...

So I am test fitting everything, installed drive and driven nice to realize the rear sprocket and jackshaft sprocket don't line up. Now if I space out the jackshaft sprocket to match the rear wheel sprocket,then the driven pulley moves forward, then the drive pulley has to move forward which...

I have a stepper motor with a 18 mm shaft and a 6mm keyway cut into the shaft. I want to mount a sprocket on the motor shaft that can use a bicycle chain. The chain my bicycle sprocket will use is 1/2" pitch by 1/8" width. I believe this chain is also known as ANSI 43. My problem is that so...

So the Coleman ct200u runs 420 chains, problem is looking at rear sprockets with a high tooth count such as 72 or higher only come in #35. So I can change the chain no problem.....but what do you think about going from a 420 to a 35 chain? It's a clone 6.5 motor with a torque converter 6"...

Looking for a front fender must be solid no cracks or breaks and rear sprocket for a boonie bike..:thumbsup:

Hello All, I am in need of a 6 hole Manco rear sprocket, 60 tooth for #35 chain. It needs to be in good shape and matching the 6 hole Manco spacer. I am not wanting a "universal" type sprocket with the oblong holes. thank you!

5" wheel set from sears el Tigre. Good shape. Cleaned the mud off to see if there were any cracks. No cracks or chunks missing. Great shape for being from 1969. Selling for $100 shipped. Will include a nos set of the the 5" turf savers I have for sale for another $60.

Anyone have pics or ideas of a sprocket brake. I think it's the easiest way to add a caliper. Anyone know of a small caliper that will work, either cable or hydro?

Looking for sprocket spacer and sprocket for 6" Manco wheel. If possible please include hardware for it too. Not to worried about hardware.

The front (small) sprocket on my Challenger is worn with "shark fin" teeth. I can't seem to find any posts that detail a rebuild or fix for this. Anyone tackled this project who is willing to share their experience? Thanks in advance. Todd