3.5hp

Bought this awesome 1970's Scat Cat mini bike around my area! Runs good and rides smooth all around. Probably going to give it a better exhaust. Pretty excited about this one! Feel free to tell me more about these beauties!

First up to bat is a just stripped side popper: H35 45455R SER 70965. Shroud, Recoil, Head, Bolt, Carb, Manifold, Cam, Lifters, Side Cover. Shroud has rust as shown, (Ouch!). $40 for all these H35 parts as shown, shipped. For an Xtra 10 bucks (defrays shipping), I will throw in the rest of...

I pulled the engine off my Trail Bronc VT-5 and it is a 3.5HP Tecumseh engine with the clutch. I still have the sticker with the model number (which says H35) and such. How can I found out what year this engine was made in? I'm going to try to clean this engine up, get it running and repaint it...

Can pick this up for 15 bucks runs good. Will this be good for small mini bike

Picked this streaker trike up during the winter. Been riding it around for the past couple weeks since we've had some decent weather here in Michigan. Rides and handles good. Turns on a dime and gives you change. Since these pictures were taken I have removed the 3.5hp tecumseh and will be...

Craftsmen Tecumseh 3 5 HP Engine | eBay

New Never Run Briggs & Stratton 148cc (3.5hp) Motor - 3/4 shaft - Threads inside shaft - ready for mini bike - $125 + $35 shipping :thumbsup:

Like new motor for sale - took out for a predator. $100 + $35 shipping

Need a Motor adapter plate to put in a briggs 3.5hp in a Motovox mbx10 . anyone have 1 ??

For Sale - 3 new Briggs & Stratton 3.5HP motors - all have 3/4 shaft and inside threads. shaft length is 2-1/2 inches long. perfect for mini bikes & go carts - tillers - edgers . Cost is $125.00 + shipping . Thanks & Happy Holidays :thumbsup:

Throwing this out here since theres a tecumseh section on this forum. I have a 1972 Sears Eska 3.5hp air cooled outboard engine that is being a royal pain in the ass. When I first brought it home it would start ok and idle (albeit rough) but would break up under throttle horribly and would...

Any ideas on a trick looking exhaust for a 3.5 hp H33 exhaust like a cast Reed muffler?....this is the best I can come up with thanks

Was looking on ebay for a stock muffler for the GX-110 I have. sn. 1711520. Mine has a round hole between the two studs but the gaskets shown on ebay are half round with a straight side, strange? Not going to pay those prices anyway but wondering if there was an early and late gx110? Should any...

Hi, newbie here! I got this briggs and strat engine that had been sitting for 2 years, brought it back to life then broke it down to convert it to horizontal drive. I have the original tank and governor but I see people use metal ones on mini bikes, could anyone point me in the right direction...

I can see it half way up the threads in the fill hole. Is that to much?

I have a new diafram. head gasket. And a carb to gas tank gasket. I've never worked on a motor with the carb mounted on the gas tank so sorry if this is a dumb quiastion. But from what I understand the longer tube picks up the gas and drops it in the bowl For the short one to pick up:shrug...

I've been searching for a 5/8 shaft lighting coil for a Tecumseh 3.5hp engine from the 1960's-70's era...Does anyone have one for sale? Thanks!

Anybody know or can measure the distance of the exhaust flange bolt holes..center-center. And i.d of the exhaust hole itself. Thanks!

Here is a Tecumseh 3.5hp complete. Original paint with complete linkage. I will ship at buyers expense. I have started it and runs strong. $200.00 OBO. plus shipping (Pay Pal purchases add 4% to total sale) :scooter:

3.5hp vs 5hp briggs both have same carb? Because I want to buy velocity stack air filter for for briggs. It's fix? Any idea. Also should i buy 5hp briggs and change the carb to 3.5hp will it gain power? Thank