bearing

Tecumseh part number 28458...anyone have a new one for sale?....It is the ball bearing type

Putting a new main crank bearing (ball) in my rebuild project. I see in the Tec manual a mention of a retaining bolt on the inside of the case cover. When I tore it apart, I noticed there was none installed. I see two holes that look like they could be used for this. Do some people NOT put these...

Anyone need this for a Benelli rebuild? Pay for the shipping and it's yours.

Title says it all. How do I get this thing out and what bearings are used? I have an idea on the removal but want conformation before moving forward. Looks like you just remove the sprocket and push the shaft out from right to left (sitting on bike). As for the bearings I am sure there are...

Hey gang, I got a nice Fox Sprite recently and am starting to put it together. I do not like the wheels it came with and was going to swap them out. I noticed the forks are drilled for a 3/8 axle. Is this stock? What is the easiest way to put on my wheels (Astro rims with 5/8 bearings) I think...

Can anyone provide the specifications for a Rupp "Sprocket Bearing", p/n 12455? Or better yet, know where I could get one?, Or better yet, where I could get an original clutch for a '67 Continental? Mine is shot, but I think it is re-buildable. The "bearing" is in the outer clutch, and...

A neighbor brought me her son's DB30 that is in ROUGH shape and wanted me to fix it up for them. One big issue I see is that the front end is really loose, looks like nearly all of the bearings are gone. I see posts about people switching over to the sealed bearings. Before I take the front...

I am looking at getting a Vortex (red) clutch for a drag bike, motor is briggs flathead. I plan on this motor having ~15-20hp but would like some room for more HP down the road. Vortex builds up their "red" design, and lack of a needle bearing. They use a sealed ball bearing keeping the clutch...

I did a search and found this mentioned before but not resolved. I just got my TS working and have gone through two sets of wheel bearings on the front. These weren't the stamped wheelbarrow bearings. Has anyone found a bearing that works well for these? All of the high speed bearings I've found...

What is the correct bearing for the rear axle for my Cat 400 with the disc brake?

I just started work on a mtd Columbia. It's my first mini and I have no experience with this stuff. It didn't come with a rear axle or bearings. Does anyone know the correct axle and bearing sizes for me to order?

Sold my Harrison project and was going to use this motor on it, so now I guess I'll sell the motor. I've had this motor for a few years and it's been on a couple of different bikes. Runs like a raped ape. Tons of compression. Probably just at the break-in stage. Maybe has an hour of running...

Hi guys, Anyone have any knowledge of the 6" steel rim posted on the OldMiniBikes warehouse site product #AZ1025 that comes with a 3/4" bearing? What I'm trying to find out is what bearing is needed to change it to a 5/8" ID bearing to suit the axle before I order it so they can be ordered at the same...

Any ideas to remove them,?

Hello guys, It has taken me a couple years to piece this together but I have finally accumulated most of the parts to make a complete Lil Indian 6000. All I am missing is the one way bearing and sprocket. Where do you Lil Indian guys get your parts from on these? Or do you just not ride them...

Is it even possible to find these any more? How much of his arm would a fella have to loose to get one?

Does anyone know of better wheel bearings for the Baja Heat/Warrior? I want to install higher quality bearings for higher travel speeds and longer bearing life.

Looking inside this wheel are the red arrows (and possibly the green, although that could be the outer ring of the bearing) pointing to a sleave or something? I have replacement bearing to install, should I try to save these? They are pretty far gone in any case. What are they?

I pickup a nice looking Bonanza but the thing pushed like a brick pulled the front wheel and the bearings just fell out and one turned hard one was seized the bearing bore's are +.020 or more the bearing is 1.375 od the next bearing is a 6203 5/8 the od is 1.574 has any body done this bored...

I recently purchased a Manco Minibike that is a mechanical nightmare. My question is: I have the Manco aluminum wheels and I need to know, Is there supposed to be a spacer tube in the wheel, between the inner bearing races to keep the outer spacers from putting pressure on the the inner bearing...