breather

PVC Catch Can ver. 2.0

Gc 5 hp I removed the air cleaner assembly to fab up my linkage because it's a pain to work on I plugged the breather hose and took a few laps on it Now it is pushing oil out of the fill plug and the govenor arm at the block Other than put the air filter box back on is there a solution for...

Hi, For my Cast iron HH70 build I had to purchase a new air cleaner assembly, I decided to go with a kit I found on Ebay shown in the picture below. It has a cast iron elbow and paper element that some of the cast iron industrial "X/L series" Tecumsehs' came with. This means that the crankcase...

I don't have any experience with small block Tecumsehs so need a little hand-holding here. Is the breather housing one piece or two? Just looking to replace the element and it appears pulling it out of the narrow slot is not correct. Also, the housing gasket looks to be sandwiched rather than...

Hey I put on a perf . Air filter on my Baja mb200 and there is a small rubber hose that has nowhere to go should I buy I filter for it and where can I get one at:hammer:

Alright guys I cam across something today that I have been worried about. My Predator 212 has seem to have lots of blow by. Its been smoking a lot and when I shut down the engine in just pull the cord slowly it puff smoke out the pipe. Im not running valve oil seals could this be the issue...

So i really like to reuse things. I like to take things and use them for a different purpose... ive saved all kinds of crap to use for something else, and many times has come out better than anything i could have bought from the store. so I have some stainless steel water bottles ive been...

So this has more than likely been asked, but a search wasn't producing results. I'm using a different fuel tank for my 212, as well as an angled air filter. With that being said, it leaves two useless hoses... One that ran from the top of the fuel tank and the hose that goes from the old air...

I need to get these parts off my garage shelves. They're nice and all, but I need to free up some money for a project. All parts are NOS and include the original tecumseh box they came in, with the exception of one of the round breather housings. It's NOS, but doesn't have a box. NOS Recoil...

So i got the Craftsman Tecumseh I picked up a couple of weeks ago running and got the idle adjustment just so. I was lightly reving it to get a good sense of the main adjustment and its ability to load up without stalling or stuttering and i swear i saw a small object fly out the breather and a...

I've been working on this H35 for a little while and got it started today. Woohoo! :freakout: BUT...oil started dripping out of the breather. :ohmy: I had read that it should take 21 ounces but it seemed to overflow a bit before I got all 21 ounces into it. Is it coming out the breather...

I picked this up a while back but ended up buying an NOS, so won't be using it on my 1970 Rupp project. The inside is really clean, but it could use a new diaphragm/gasket. The breather housing needs a paintjob, but it is in really good condition, and the filter screen is in tact. Has an intake...

Hi guys, Picked up an old h80 Tecumseh . Cleaned the carb and got it running . Changed the oil and was careful not to overfill. It runs strong and idles perfectly but oil is dripping out the breather. It does not smoke at all. If the rings are worn would it not be pumping blue smoke out the...

Looking for an original Honda Gx160 air breather assembly....or just the top cover with filter and wingnuts. I have the lower base with the air breather post but I'm missing everything else. Free is best but I can send some cash too....:thumbsup: Thanks!!

Question... I have a 71 Rupp Hustler with a HS-40 how much air should be coming out of the breather? I have a lot. More air comes out of the breather than the exhaust than the tail pipe at idle. Any suggestions. Couple of pics of the bike. Thanks.

...mine for instance...I don't like it. I got this one off ebay for so cheap I couldn't refuse giving it a try. I just don't like the looks of it. :surrender: Maybe, if I used a 90° fitting... :shrug: Anyone have a suggestion? Please post some pictures of what you came up...

Anyone know where I can buy on that fits the existing hold in my valve cover? Is it a 9MM or should I get the 12MM? I see them both for sale. Can someone please let me know which one fits best. Thanks in advance

all of this 20$ plus shipping. located brewster, NY 10509PS filter is kinda bent up. honda gx/clone/predator

I just ordered a a/f kit, jet kit, spark plug and throttle plate for my Red Clone from OldMiniBikes. I have a header for it. My question is what do I do with the breather tube off of the v/c?