coil

Will a bad coil cause an engine to start and shut immeditly off, the carb is way clean

need flywheel for 5 h/p Tecumseh engine p/n 30755 for light coil

Hey guys i have a rumming but needs some work Tecumseh h50 with a lighting coil on it that runs and is on one of my old bikes and i am needing to save up for college so im wondering what its and if id do better selling it seperately off of my Herters bike. Here are some pictures of the bike and...

Decided to go a different route with my build off bike so I don't need it. 70' hs40 with lighting coil. Runs good. The recoil was replaced. $250 plus shipping.

I bought a H50 Light coil and flywheel from and OldMiniBikes member to convert my non-lighted coil H50 into a H50 w/light coil. Prior to install the H50 ran perfect and I heard after you remove a magneto it's very heard to get back into correct position. But I still thought what the heck I will give...

Anyone seem the NGK hot racing coil selling on eBay for gx200 / clones ? Anybody bought one yet and is it a performance coil and if so how well does perform compared to a stock coil. Anyway to increase spark output of a stock coil ?

Anybody had or have any experience with a NGK hot racing coil that's being sold on ebay for a gx200 and clones? I seem to think maybe seller is being dishonest by just changing the wire and boot to a different color. Can't get the seller to answer any of my questions about the the performance of...

Hs lighting coil and flywheel for sale. Works. Can be yours for $135 shipped to lower 48

Does anyone have a Tecumseh lighting coil PLUG...I have the one coming off of my HS40 (no problems there)...but I don't have the female (or is it male, lol) end that would connect to the actual mini bike.

These are from a GX200 Honda generator. Shroud is all aluminum. Has some tar on it in places but some elbow grease will be fine. I believe a gx 200 long starter cup will work with shroud or some how making a cup longer by cutting and welding. The coil is a big block coil and the bracket is to...

I just installed the new ARC Billet Flywheel and thought I would share a small idea I had. I wrote the coil gap on the coil for future reference. Also notice how I slide the air filter rubber past the mount and then clamped it down, it now has no way of slipping off if hit while off road. Cause...

Hello - Does anyone know where to purchase an ignition coil for my Tecumseh HS40? The bike has lights. Thanks Tom

Many months ago I bid on this "lighting coil" and was the only bidder so I "won" it. It was only after that that I learned of the need for the flywheel to match and the fact it isn't complete. But now I'm wondering if this part can in fact be screwed into any stator to make it into a lighting...

Found this complete H30 from an ARCO today. H30 35260H 1971. Even all the minibike throttle linkages are there and connected. All silver this time.. No spark or compression. Not stuck at least. Havent opened it yet but hopefully its nothing major. Looks like the original carb too...

pickd up a used 6.5 clone this week. Has no spark. Disconnected switch and low oil sensor. It has oil in it. Still no spark. I took the coil off. Is there a way to test the coil? Thanks.

My Yard Marvel Mountaineer Model 6-439 originally came with lights and a lighting coil. I have an era correct Briggs 6hp, but need the lighting coil and flywheel. Thanks!

New 2007 Honda GX160T1 QXS2 with Lighting Coil- Standard 3/4" crank keyed I believe 2 7/16" long 5/16"nf tapped. Engine was just removed from box to take these pictures. I have had it since 2007. The tag says it is a 50 AMP coil but pretty certain it is a 50 WATT charging coil. At 50 amp this...

have a lighting coil and flywheel off an h5o for sale $125 shipped :thumbsup:

Does anyone have a magnetron coil for a 3.5hp Briggs that they might want to sell? I have an older Briggs that has points that I want to switch over to the electronic coil. (Not getting any spark right now)

Well I was able to remove the carb from my other post and get that cleaned... but now I'm not getting spark. I removed the fly wheel and coil that's under it but like an idiot I forgot to mark the spot of the coil. With that being said How do you set the gap between the coil and magnet if...