This was part of the a/c system on my Firebird. I was going to scrap it but then thought it could be used to make a cylinder gas tank. It does have pipes running inside of it and you'd probably want to get rid of the part with the fittings anyway.
Figured I'd throw it up here for free if...
Brand New hemi head/complete (valves, springs, rockers, gasket, etc). hemi carb, push rods, lifters... and flat top piston, with rod, all new take off...
located in SoCal... $70 shipped
Are these heads both the same casting? And What size are the stock valves? I have a gx340 thinking of a nice port job and some stainless valves but can't seem to find the stock valve sizes. Thanks T.J.
I have a new style Predator hemi engine and I am very confused about at kinder heads. I have been reading about gx160 head usage in clones but is this advantageous in this engine? I also see 18cc heads....I guess I am just confused about head compatibility of this engine. Or am I best off...
I'm in search of an H35 side pooper cylinder. I have all of the other pieces to complete the engine, just need the cylinder itself.
If anyone has one they would like to sell, please post up! I'd also consider a short block if the price is right.
Thanks in advance!
Daniel
Small gas tank, 8" X 3", clean inside, no dings. Cap neck threads are mangled as shown in pic, but the cap will thread on. With brackets.
35. shipped
FantomResto@hotmail.com
602 705-6557
Anyone else have problems with oil in the cylinder of their predator? Ive got a predator with about 12 hours on it and there is a good amount of oil getting in to the cylinder. Im not sure if the rings went bad or what? I took the head off and there is oil pooled up at the bottom of the piston...
I just received my eBay special. This is a Power Products Model 300 opposed twin 2 stroke. It has a steel cable pull start and a top mounted tank. I have not seen a lot of these around. This one is very complete, has great compression, although I have yet to test for spark. If it has no spark, I...
I have a briggs vanguard 14hp engine and it has an oil pump inside of it plus the oil filter on the side. I was wondering if it would be possible to convert it from a vertical to a horizontal and what is all involved
Looking for a nice or nice enough I can fix up to be nice cylinder gas tank, nothing huge just something to fit on a Ruttman frame. Shoot me a pm or leave a post here if ya got something.
I'm going to buy a cylinder hone to deglaze my aluminum bore briggs. I've looked around on OldMiniBikes warehouse and ebay and I know that with an aluminum bore you need aluminum oxide stones. But the 25 buck one on OldMiniBikes doesnt only says the grit of the stone. Anyone know the stone material?
So i got this briggs and its pretty messed up inside so i think im gunna hone it so first question is do on need a joneing drill bit or can i use sand paper? Also when im done how do i know what oversized rings yo get??
i have a kawasaki bayou 220 i just got to working on it and have spark. i new when i was putting it together it had low low compression but figured i could ride it a little while and it just would burn oil. well it won't even fire i have a brand new piston and rings for it but don't have a hone...
I bought 3 for a good deal, needed one and never used the extra 2.
Part number - 210812
May fit 2hp motor also.
Does not fit 3.5hp motors
Looking for $20 each shipped.
USPS - Paypal
California
I would like to call this head NOS but not sure. I bought it a couple years back and it came in this old Tecumseh box. I can't really call it new either because I installed it, worked on the engine a couple days but never got it to run so I went a different direction. I filed down one of the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.