cylinder

This is for a mini bike. I'm looking for a complete set up if possible. I would like to buy the brake lever w/master cylinder on it to go on handle bars. I also would like to buy the caliper and brake line that goes with it. For disc brake set up. thx.

This is for a mini bike. I'm looking for a complete set up if possible. I would like to buy the brake lever w/master cylinder on it to go on handle bars. I also would like to buy the caliper and brake line that goes with it. For disc brake set up. thx.

This was a New Old Stock gas tank that I sent out to have chrome plated. It WAS absolutely perfect, in every way. After many, many months this is how I get it back. First of all, some moron must have dropped it because now there are two small 1/4" dents on the end. The chrome plating (if you...

hey guys i need a rear sproket 68-70 for a 4 bolt hub. also i bought a clone engine and the fuel tank was to tall for the frame, so i also need a cylinder fuel tank no more than 4inches in diameter. let me know. ill post pics in the morning to let you know what im workin with. thanks (im...

BRIGGS & STRATTON CUSTOM 4 CYLINDER WI ENGINE - eBay (item 160496174602 end time Oct-27-10 13:24:47 PDT)

I don't know if I need to straighten the forks the front tire may never touch the ground.

winter will be here soon, and i will be tearing the motor down, looking to just get a complete done up head, AGK? Or NR ?

I Am looking for a good Mild cylinder head for my gx200.. Should i go with 14cc, 18cc or 22cc.. and can somoene explain how to do an 8 degree timing. Thanks You Current mods: -arc rod -.308 cam -arc flywheel -Mikuni carb

looking for jlo parts or a whole engine

60's era Engine. Are they just plain aluminum or Nikasil plated? Which Flex Hone you guys using on these? Aluminum Oxide or Silicon Carbide? Thanks KD

Looking for a cylinder head porter and valve job for my GX160, in michigan.

anyone got a good source on a rebuild kit on the master cyl. on a 1969 chevy C50? Tried all the usual suspects (napa,schucks,etc) to no help, they dont even have a listing past a C30. and my web searchs so far are not fairing much better. theres only a bazillion of these old farm trucks still...

I am looking for a Cylinder Head in new or almost new condition. It has to be a single tab head with good metallic paint on it like the one in this picture. Thanks

Will a spring loaded, stone type hone take off more material than a ball bottle brush type hone? I have to hone a couple engines including a gx390 and a 6.2l diesel, and want to take off the least material required for honing to enable the rings to sit properly. So, which would be better for my...

I've been wondering if it would be of interest to some forum members if I were to make and sell stainless 4"x6" and 4"x12" stainless tube tanks, unless somebody is already doing so. They would cost somewhere between $60 to $85 a piece, depending on size. They'd come with fittings and gas caps...

looking for a cylinder gas tank. looked on the net but thought that someone makes them...

I have for sale a round, cylinder , PLASTIC gas tank. It is 8" long and 3" wide. It's used but clean on the inside. $30 delivered to the lower 48. Pm me if interested.

i have a tank for sale it is 8 1/4 " long and 3 1/2" wide it does not leak !! it has a inlet and threaded nipple it just needs to be repainted it has slight surface rust only no holes!!! this is a solid tank not junk. i will take $100.00 plus shipping. you can email me at fallonjm@yahoo.com

how far can you bore out a 5hp cool bore block? i got a block that was ran with low oil and has some cylinder wall galling.

I Was Just Wondering Where Everybody Gets There Cylinder Tanks For There Doodle Bugs? Any Help Is Appreciated.