mount

I have a project ive been working on lately its a 1969 duck bird. I just recently got a old 5hp flathead briggs that I was super exited to use as its engine as ive really only used predators before and I thought it would be perfect for my vintage project. It was kinda a fast thing I saw the...

Looking for an engine mount for my little petro. Might have to build my own but figured I would try and find an original.. Also will need a seat and chain guard... I know it's a long shot lol.. thanks for any help.

What's going on guys. I need some suggestions to fix an issue I created for myself on my build-off bike. I'm running a predator 212 hemi and I had to use a 15 degree engine mount so the torque converter would clear the frame. I'm running the stock engine mounted tank. The problem now is most...

Looking for the upper forks/triple tree with headlight/number plate mounting ears, for 1971 Speedway with 10" wheels. Please let me know. Mike

Recoil, doesn't catch starter cup, I assume that it needs new paws on the recoil. Did run before recoil stopped grabbing. Cw rotation at the crank. $175 plus shipping.

Hew everyone i remember a few years back that OldMiniBikes sold just the Clutch Guard Mount for the predator but i cant find it now, i can find the full kit but but i was just looking for the L plate that mounts on the engine, anyone have leads on them or able to make them?

When you mount an HS40 on an angle, do you need to reduce the oil capacity? I have 21 ounces in my 80's HS40 but the angle mount dipstick says it's over capacity & it's full to the filler neck. thoughts?

I read the Tecumseh HS40 motor takes 21 ounces of straight 30 oil. (My motor is an 80's model) I have it mounted on a slant on my FOX Spoke Wheel mini bike. I poured in 21 ounces of oil & the dip stick has it above the safe line. (While slanted) the oil is pretty close to the fill hole, so...

Hi everybody, the season is near. looking for a motor mount for the sachs 80b, widow maker. theres gotta be one out there somewhere. thanks for looking.

And, the project gets closer to completion, due in good part to the help and info from members of this forum. My son and I are down to the point of mounting the Predator 212 as a retrofit for the original H50 on this bike. Based on the mock-up, we have to raise the front of the motor by 10mm...

Hey guys. Looking for a clean solution for mounting foot pegs to an Azusa project bike. Has anyone used a handlebar mount like this? I hear a lot that the cheap clamp mount that come with the bike suck.

US 820 motor with repro engine mount sale is for one engine, $400.00

There're lots of discussions on Tachometers and which one is best to use on a mini bike but, I don't recall any on how to mount one. I wound up getting a cheap one off Ebay and installed it on the handlebars temporarily using safety wire. :001_huh: I thought I'd eventually get around to...

The all most unheard of stellar top mount gas tank. Not gonna build this bike so no need for this anymore. Outside is cleaned down to bare metal. Inside is clean as well. One little dent in top of the tank. Original gas cap. No fuel petcock. $300 shipped and insured. My packages like this are...

This has never been hole mounted for a TEC or BRIGGS It is meant to have a engine like this but, I'm sure not a 50cc Yamaha dirt bike engine. This engine however, fits the location perfectly. Has one spring under the steering Colum for front suspension, like Cat bikes do. Please, What is...

Ran into a potential issue while putting a west bend together, I had the late model shroud with the widefoorprint recoil on it previously and decided to retrofit it with the more appropriate shroud. The fairbanks recoil mount holes are larger than the threaded inserts on the shroud, I made some...

I am starting a restore project, I need to replace the rubber bushings connecting the motor plate to the frame. Does anybody know of a website or seller that carries these? I figure they must be a automotive leaf spring shackle bushing, but for what vehicle? TIA

I need a mount for the little round "Cylinder" gas tank that was on an old Clinton 2 stroke motor. Any help would be appreciated. Gary M

What's out there. Will the one OldMiniBikes had for the 580 work if I cut the other part down. Is the pto mount pattern the same for a 580 and 610

Selling this great go kart setup....40 series Comet torque converter, with an under engine jackshaft mounting plate. 1" bore on the clutch. Shown on a Briggs OHV engine. Engine is NOT included in this price. Asking $150 plus shipping. Or best offer..... Usps postal money order, cash or...