starter

Hello too all,Am selling this kickstarter for parts or rebuild for 110 bucks shipped to you.It is broken.Good for a bike that is a shelf queen.If interested just reply and i will get back to you.I am only accepting a money order from the post office or cash on local pick up in levittown n,y...

I need a recoil pull starter for my new project; an 8 HP trike from MW. It's a Tecumseh HM80. Needs to be working and ready to go. Thanks! Roadmaster75

I have a brand new Fairbanks Morse pull starter. This will fit Some Tecumseh's, Kohlers, and West Bend engines. This is in a Kohler box, but FB made these for Kohler. Labeled FB on inside. This is NOS and has some shelf wear. Cheaper on OldMiniBikes than eBay at $110.00 shipped. PM me if interested

Finally her it is a non- smoking non-knocking very fast strong running engine. I took this off of a minibike a about 2 months ago and put it on my shelf. I know I must be crazy for selling this one, I probably will never find one like this again. I stand by all my sales, Mac, and George3 can...

newbie question but when adding a starter nut to your crank shaft do you use it in place of the nut holding the flywheel or just add it to the end of the shaft? thanks in advance.

I was pulling the starter rope on my Go Devil the other day and it went slack. So with considerable effort, due to the old screw heads being stripped, I removed it and found that it's pretty different than the regular normal stuff. It has 2 sharp teeth ,one on each side of the spring...

can I rotate the starter on my predator 212 so it pulls up instead of out toward the front of my bike ?

Can't tell if it has the pull starter or not. Vintage Mini Bike Vintage Mini Bike - $175

I'm currently looking for any Tecumseh and Hegar kick starter parts. I have one of each in need of repair, and I wanted to see if anyone has any parts lying around for them....

I would like to install a starter motor on my Super Bronc that has a good running Tec H80 on it and no mounting holes for the starter. I bought the flywheel and the matching 12v starter motor from a lawn tractor engine. Has anyone done this successfully? Is there anything I really need to...

Those pesky snowblower engines usually have the big hole punched out for the 12V starter :doah: I started building an HS50 to sell and as I am putting it together the big ass hole caught my eye. So I made this cover on the fly this morning, its nothing fancy by any means but it covers the hole...

Looking for Tecumseh starter motor part #35765A for H60. I see them all over Ebay for approx $50 - $70 new. Hoping to find one quite bit less than that. Can be used. Thanks

Its amazeing what these Kick Starters go for. Vintage Mini Bike Kickstarter | eBay

My class made mini bikes powered with Toyota Car starters. This is one of them.

Will a 99cc clone pull start fit a gc160? its the same as the 79cc one and probrobly the same as the bigger clones but im not sure? Thanks :thumbsup:

first time i've seen this. looks simple enough to do. i would like the kick peg to fold for more clearance though. should have enough parts laying around, just need time. https://www.youtube.com/watch?v=2LsyhjhWgLc

Havent seen a Predator up close yet but can the recoil starter be removed and rotated to put the pull rope in a different position? Thanks!!

Got this old pull starter with the cool art deco handle i dont know what its for. Looks like its designed to be either cw or ccw with a few different parts. Thanks

Looking to buy a recoil starter for a 212, in good condition with 212 sticker on it. They are $30 plus shipping on ebay. Looking to buy for less.

I picked up this little beast today ... needs a little tinkering to prepare for Detroit's seasonal deluge of snow (total 94.8 inches this last winter) I can order a Chrysler Marine F15582 starter rope by part #... Great, but if I knew the size and length I could pick one up locally at a...