starter

Fairbanks Morse starter cup

I have a orange briggs animal thats set up for a kart electric starter i would like to set it up with a recoil starter to use on a mini bike....the briggs local option LO 206 has a recoil starter would these parts interchange?....if so which parts would i need and part #....also whats the...

Homemade electric starter... a little cumbersome, but it's an option for engines in which recoil has been removed. Not sure exactly what they set it up for, but I'm sure a handy shopsmith could mod it to work in whatever fashion desired. cables hook up to a standard 12-volt automotive or...

My daughter has a hard time pull starting her 8hp Tecumseh. I got a 7hp tec with a lighting coil and a starter ring but the bore was shot. I had a 6hp tec, it was a good candidate. I put in a new piston, rings, lapped the valves, ground the head .030, new carb. The lighting coil...

looking for a H50 or HS40 kick starter email me at csmolen@advantagestarmortgage.com

Tecumseh H50 BLOWER SHROUD with RECOIL STARTER, plus, original Hardware & foam cover. -original paint- $25 (plus shipping) Pull-start recoils nicely

I finished rebuilding the West Bend 820 on my Chrysler Sno Runner. Both the recoil starters I have do not engage the "Cup", which has many gouges in it. When looking for a replacement cup I saw one advertised as a right hand "Cup". Is there a difference in starter cups on WB right and left...

Thinning out the stuff a little. The older box on the top right has the wrong part number on it FYI, the recoil cover was just in that box when I got it... Everything you see for 50.00 plus shipping (be patient) from 12302 zip in NY or trades for Trail Horse/clone/predator...

Hi All I just tuned up a briggs carb 3.5 and it will not start and run without fluid. I'm not good with Briggs. It idles, runs and throttles up fine until it is shut off then wont restart without fluid. What am i missing? Thanks Xander

Did a search, nothing ... I have a mid 70's Heald VT-8 that I would like to add a starter to. It has the hump in the shroud ... Is the motor an H80? Do I need to tap the block? What starter? A snow blower starter with the starter button attached would be OK. Suggestions...

This is the old school aluminum cast pull start with the round blower housing. It has a couple dents, but otherwise in good shape. Like all old Briggs pull starters, this could use a good cleaning! $40.00 shipped lower 48 willing to trade for smoked salmon only!

I need a starter cup for a tecumseh that is at least 2 and 1 /2 inches inside so I can use a wind up starter.

For those of you with the built up high compression engines. What are you doing to start these things? I just installed my built up briggs 305 onto project K&S and tried to pull start it and it almost took my arm off. Starters are expensive from what I found online. Have any of you DIY one?

12v Electric starter - $75 + shipping (paypal as gift) I have tested it with a battery, it works great. 14 lbs

Has anyone made their own kick starter? I feel like it would be fairly straightforward, except for the disengagement part. Are there any good pics around of how these are designed? I would like to give it a shot. Thanks!

25 pickup or 35 shipped 12V starter works good. May fit other engines. I have other parts of the same engine available send me and email and ask. https://drive.google.com/file/d/0B0v4U_rswuqdQ25acnFGLVVXOEU/view?usp=sharing...

Fairbanks Morse pull starter for Tecumseh engines nos with slight shelf wear located in Wilkes barre pa $35 +$7 shipping PayPal

All prices do not include shipping. I will ship all the engines and bulky things UPS. I have included the unpackaged weight and you can run rate quotes yourself from zip code 83864. PM me with any questions. Thanks! Briggs & Stratton 4HP - $50 This engine runs great and seems to be real low...

This likely wouldn't be too practical on a minibike, but perhaps may be of interest on a go-kart project. Electric starter motor to bolt to the front of a blowerhousing; not sure as to whether it's a universal design, as there's no instructions in the box, but this starter motor utilizes a...

Looking for a working 7 hp Tecumseh with starter or starter mounts at minimum. Going on a healed VT7 and trying to stay close to original. Thanks