troubles

  1. red baron

    sears mini bike wheel troubles

    Hi guys, I just picked up an old sears mini bike that from what I can tell is the same as a Bird Wren. I bought some 4"wheels and the rear hub is way too wide which is throwing off my alignment. I found pictures online of this bike and the sprocket hugs the tire. With this set-up the sprocket...
  2. H

    Pay Pal Troubles When Ordering from OldMiniBikes Warehouse

    On my last order and now again today, I can't get my Pay Pal account to work with OldMiniBikes. Goes like this: I hit the checkout button, and select Pay Pal as my payment method. Then the Pay Pal screen (their website) opens up and asks me to log in. I do. The screen then goes back to OldMiniBikes with...
  3. M

    tillotson troubles

    so i got a ec birt hl334wx dominator plus gas carb. i put it on and got it fired up relatively quick warmed up the engine putted around a little kept stalling due to not having set any idle yet per the instructions that came with it. ran awesome when i was hitting the gas. this is a step up from...
  4. M

    Tillotson tuning troubles

    Hey everyone I got a tilly hl 334 ab on my flathead briggs, I'm having some trouble tuning. As I'm coming out of a turn at slower speed and hit full throttle it pops and dies but when I let off the gas it starts to go again. Any suggestions what I should do? I'm running gas, pop off is at 10...
  5. gumpit

    Anyone else having troubles with pics opening?

    Some of the pics I click on only open up halfway and the bottom stays grey. Never used to. Is it just me? And its not all of them either,just some,
  6. B

    Tecumseh Troubles

    Hi! Im new around here and figured you guys would be the best place to turn for help.. I have a Lil Indian Minibike with a Tecumseh H40 on it. Its about 10 years old or so. I know its probably a little new for this site but I figured I give it a go. I would like to "Hop Up" the little H40 as it...
  7. C

    Tillotson tuning troubles

    Well finally got the carb on the motor and running but not exactly right. It seems to pull away from a standstill fine but as you get up in the rpm's it starts popping and cracking(sounds like an old machine gun) then all of the sudden it takes off and goes like a bat outta hell. Now I'm a...
  8. H

    tecumseh troubles

    just installed new carberator and now it idles but once i rev it up it wont idle back down what to do now ?
  9. E

    Baja Heat troubles after mods

    This is my first time posting on the forum. I'm having some trouble with my Baja heat after I did some engine mods. Recently I installed a Billet rod, aluminum fly wheel, 18# valve springs and a 90# main jet. My problem is that the motor won't start or stay running. Today I had the chance to...
  10. Harleys Papa

    Tube troubles

    I have 3.00/10 tires and I cant find tubes that size with straight valve stems:out: I can get 2.75/10 or 3.50-4.00/10 do you think either of these will work? Thanks Randy
  11. T

    Baja Racer 97cc engine troubles

    Hello, First post... I have a Baja Racer 97cc mini bike just a year or so old. My friend who owns it said it ran good for a while and it just seemed to get weaker and weaker until it just wouldn't start any more. He brought it to me and I found the carb loaded with carbon, a weak spark...
  12. larkija33

    Throttle Troubles

    Hey everyone, So I have a Benelli Buzzer, but inside the throttle there's a block holding the throttle cable that cracked. We took it out, finding that a pin on top of it that slides in the handle is completely gone. Anyone know where I can get one just like it? Thanks. I'll post a picture...
  13. johnf.357

    clone clutch troubles

    I have a 6.5 clone stock,just got the kart with this set up,it has a noram clutch the cheap one,and when I drive it the clutch slips,over heats and omints sparks,all not very good.I am told it is because the clutch does not like stop and go driving(what I do).. I want to switch to a max torque...
  14. S

    Briggs Troubles Help!!!

    hello, today i was riding my minibike in the cold weather. And when i was riding it the centrifugal clutch started screeching and my pull starter rope started to unwind. Does anyone know how i can fix the problem of my centrifugal clutch screeching and the pull starter rope from coming out too...
  15. M

    shear pin troubles

    i have a 5hp briggs that i'm trying to get running. when i was checking the coil for spark, i removed the fly wheel and put a 1/2" drill on the shaft to turn it over. it turned over very easy, of course, and there was no restriction. when i replace the flywheel and recoil, it will start, but...
  16. S

    5 HP B&S Throttle Hookup Troubles

    Hello i'm new to this site, i have searched the b&s part of the website, and i just cant find out how to hookup a throttle for a 5 H.P. Briggs and Stratton It's an L-Head. The throttle is underneath the gas tank. it's the kind were the throttle tab slides in a slot cut in the bracket underneath...
Top