crank

I was reading on NR racing website that you can install a Arc billet rod but , crank must be turned to 1.180" to install rod. I have not worked on small motors what's required to remove the crank and install it? Any special tools anything to consider? Replacing the rod seems pretty...

Well i took the side cover off what i thought was a stock briggs 5hp to a cam change and realized that it has a billet rod and lifters. The crank also has a ball bearing on it, how do i get the bearing off and put it back on so i can change the cam. Also the cam has no markings on it at all does...

used but in good condition. located in so cal. asking $40 shipped

Looking for a early CLEAN stock Briggs crank, I purchased a very clean early 5hp but it has a stub crank. Thanks

I have a real Honda GX160, 5.5hp that came off some kind of pump. The guy sold it to me because the bolts in the side cover broke off. It was running fine, but he didn't want to mess with it and bought a whole new engine. I wanted the head and a few other parts, and I have no need for the...

Need good 6.5 hp honda clone stock crankshaft.

I am looking for a 5hp briggs small bearing crank and bearing. If you have one pm me price.Thanks.

need a crank for my GX390 13hp Honda,OEM would be great but would take a clone crank too.

Hi All, Looking for a stroker GX200 crankshaft, with matching conrod. Preferably ARC's .175" Stroker & Rod, must be in good condition. Post back or PM me with details & Prices. Cheers, Dan GX200 tuning store UK

Pure power billet 3 inch stroke crank for raptor or blockzilla, etc. 7/8 journal, 3/4 keyed and tapped shaft. Bought it to build a wild raptor, but I just lost motivation. My loss, Your gain. I'll include 2 ARC rods as well, 1 4.225, and 1 4.275. $150 shipped to your door.

lol this is interesting Tecumseh 3.5 HP Engine Crank Start

Looking for a 4 hp Briggs crank. 5/8 or 3/4, doesn't matter. Changing out a gear reduction set up. Many thanks, DAN

I changed the crank out in my engine and the new crank that I put in has multiple timing marks so I put it on the mark that was notched and now it won't run at all, it feels like the engine is retarded timing. I put it to top dead center where the magnet lines up on the flywheel and the rod cap...

I have a brand new in box ARC .175 stroker crank, ARC stock length billet rod with bearings and a std. bore Honda flat top piston set for sale. Rod and piston are for stock crank. 225.00 shipped for the crank. 55.00 shipped for the rod 45.00 shipped for the piston, rings, pin and clips

A whole BUNCH of crap showed up at one time... Ben wanted 75 bucks for all of it.. So I bought the 71 Briggs 4 horse bearing motor in near perfect shape still on the tiller... STICKER STILL ON THE GAS TANK :ohmy: Started and ran awesome FIRST PULL!!! on ROTTEN GAS!! STILL AT THE JUNKYARD :doah...

This is a genuine honda crank that has been turned down to a 5/8" straight shaft (started its life as a tapered shaft). It is tapped and keyed. Its ready to install and go. The journal is in great shape. I'll ship it for $40 lower 48. Its in like new condition. Paypal prefered. If payment is...

we have heard a few times how do i change the crank in my block . well here we go .....read part one http://www.oldminibikes.com/forum/engines-modifications/46177-how-remove-flywheel-rope-trick-way.htmlif you still have the flywheel on the motor if not lets get going ok well we want the crank...

I need a 3/4" shaft crank for a briggs 5hp

OK so I need to cut the output length down not a big deal my problem is drilling the hole in the center of the crank . Right now the hole is 3/8-24 I need to retap it . !. what drill size do I use for the 3/8-24 tap ?