Hello, Yesterday my friend centered and drilled the crank on my 3hp briggs on his Milling machine/drill. I am glad and very appreciative for all the input and genorous offering for assistance. I installed my salsbury clutch and engine. I was probally able to do a whole 10 mph battle speed at...
I was lucky and found a nice old 3hp briggs and stratton 1959 same year as my Tote Gote . Here is the problem I have. The output shaft on this engine has no hole and is not tapped. There is a small countersunk hole in the end. I need to drill and tap this crank shaft to fit my salsbury clutch...
looking for a new or excellent cond raptor crank for a stroker build in my WF..
Looking for any other parts for the stroker build like crank gear, new piston...ect
I was thinking of this the other day and thought it might sound cool.
I know they sell timing gear sets for small block chevys for this, but I never learned what exactly makes the whining noise.
Any input ???
Alright guys ill try to explain this as best i can. I need a clutch for my briggs 5hp but the problem is it has a 1in shaft. The clutch is going to cost me $119 but a clutch for a 3/4in shaft is only $29!!! Is there any way i can take my crank to a machine shop and have them turn it down to...
I have an HS40 that needs rings. I can feel grooving on the fly-wheel end of the crankshaft. Likewise, I can feel grooving in the block where the crankshaft exits to the flywheel (there is no bearing). The grooving isn't terrible, but it is definitely noticeable by sight and by touch. If the...
My 5.5 ohv briggs is running fine but I went to grease the clutch bushing and noticed some end play on the crankshaft it is pretty noticeable and is the clunking noise I hear from time to time! I dont generally open small engine cases but need to start! I can't afford shop rates in this economy...
Looking for a good used or nicely priced new crankshaft for a 13 hp honda gx 390. Would also buy a rod and crank together if the price is right. thanks
So my bro in law changed out the coil packs in this car he just got. They were free and right there easy to try.. NOW we are wondering if the crank sensor went out. The chiltons manual says they are located in different places not WHERE :doah: I was just curious if anyone knows off the top of...
Hello everyone, I have a B&S 5hp flathead, that seized up do to lack of oil. if i put a pipe wrench on the keyed part of the output shaft the piston spin but not easily. I think I threw the bearings, since its a model tat uses bearings not bushings. But what is the possibility of the hardened...
I bought a 5 hp crankshaft on ebay and put it in my motor but the 1 inch part that turns into 3/4 for the clutch is not long enough to go throught the crancase bushing all the way. The 1 inch part stops right at the bushing instead of through it. I put it together and put oil in it and turned on...
Hi, I need a crankshaft for a Tec. H25. Looks like the clutch got sloppy and tapered in down near the bushing. I'm afraid it might snap while riding. Thanks
Pat
I cut off the 1 inch shaft, left room to drill hole and tap with a 3/4 tap.
I have a grade 8 3/4 bolt I mounted into it but when I turn the crankshaft, it is very, slightly crooked when i turn it.
Any suggestions on how to get it straght after I already drilled and tapped?
What about...
I bougt a Biggs 5hp for my Boonie Project. The motor came off a tiller and has a shaft that is 1.25 inches. If i reverse the clutch (gears in) i can get the cluch stable enough. Do I need to extend the shaft to go all of the way through the clutch? if so any ideas?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.