fixed

My Dorothy project has been on simmer while other projects have taken precedence. jeep4me needed some struts made for this bonanza ... also at some point in it's life someone hacksawed the fork lowers off because everything was frozen ... Some PB Blaster, a torch, some 1/2" dowels and a lot...

Here is my motovox mbx10 build. Perfect spot for the gas fill!!! New seat. Old one was cracked. All new controls Including Hydraulic Brakes. Here is how I modded the original tank to work. All I did was bend the original mounting brackets 90 degrees and bolted them to a old scrap piece of...

I don't think so but I wanted to ask. This arrived in the mail today and in my opinion due to laziness it was ruined. Absolutely nothing in the box to protect it and it rattled around like a marble in a tin can. Box was way to big and it had lots of room to move around. The box looked like it...

Aside from linkages, are the new style Pulsa-Jet carbs the same for 3hp to 5hp? For example...a model 135202 with detent choke vs. my model 90202 with spring loaded choke? I want to put the 5hp carb on my 3hp but dont know if theyre calibrated differently.

HS40 Snowblower engine, fixed speed. A new one on me: A carburetor with no butterfly! Maybe it is common and I just never noticed before. The butterfly is built into the intake manifold and is connected to the governor of course. If I wanted to use this engine, can I put a regular...

The Speedway tank is clean inside but has a small hole on top in front of the gas cap & can be fixed easy. $35 The other tank is ?? $15 Both tanks plus shipping

Dont know if anyone needs it or not..... Late version from around a '95 shroud/pull start/backing plate and fixed postion throttle. The recoil is they type thats pre drilled and setup for the optional bolt on external lighting generator (if your lucky enough to find one.) Shroud is clean...

Bird/Sears drover roller for sale. 5" wheels. Scrub brake. Cleaned the paint off of the handle bars and there was some good chrome under there. It is pealing in places on the inside in between if that makes sense. Seat is original but poorly fixed with duck tape. So I will be adding another...

ok I have a live axe Murray explorer. when the kids take off I hear this loud pop. there is no way that I can see to adjust the slack out of the chain. the axle is fixed. the secondary drive shaft is fixed. there is no way to move either sprockets forward or back. but I have about two inches of...

Super bronc fender. Has a Crack and some denting. Is not mint in any way shape or form. Needs repair but can be fixed and rechromed. $30 plus shipping from Grandville mi

Hey all, I have decided to postpone the 5hp, and do a 3hp. It's a runner, but not by much. It smokes oil AND fuel. The tank is pretty nasty inside, the rust comes off when you touch it :hammer: Just tried the gravel and water shake around thing, seems to be working :laugh: I have the motor in...

Not a minibike part, I figured Id post it up before it went in the trash. NOS take off, fixed speed control rod for the 5hp flathead. It might fit others too $3 plus ship cost.

NorthernTools has GC160's with fixed throttle on sale for $189, that's approx $205 total including sales tax. The ones with manual throttle are approx $41 more. Very tempting for me, because I have been looking for a used one for sometime, and used ones are almost that much on ebay and CL...

Hi to all. I am in the process of finding a carb for my 1976 HS50 tecumseh engine. I had a 2004 H35 powersport tecumseh carb that I would like to use. The problem being is that carb is a fixed jet carb and set lean from the factory so it barely runs the 5 hp engine. My question is can you jet...

I pulled off a Honda G150 3.5 hp off a snowblower this weekend, it has a fixed throttle to run at full rpm's. I can get her to run at low speeds when I pull off the governor spring. My question is: can the throttle be modified to run my mini -bike project? Or should I forget about it and buy a...

Has anyone ever tried to drill the main jet on a fixed jet carb? And if so what size did you drill it to, and did you have any success?

i patched the gas tank on the honda express and put it back together and took it for a test ride around the block. Then i parked it and when i came back 5 minutes later, there was a puddle of gas and i thought- oh great, the tank patch didnt hold but i poked my finger under the tank and no...

does anyone know how to make a fixed axle that is bent straighT?

Well, I fixed it up enough to ride around but it still needs some cosmetic work done. I put all new chain, sprockets, and bearings on it. I also swapped the motor with a reliable 3hp one. The torque converter is toast so I had to put a centrifugal clutch on it. I bought a nice clutch cover...