I have a non-hemi predator 212 and the crankshaft broke to the point where i can’t put my torque converter on. I’m trying to find a replacement part for it but all I can find specifically for predators are hemi cranks. I don’t know if those are compatible or not. I also found a tillotson...
What about using a tune pipe eXhaust on these motors?
Thanks .
I already bought aftermarket pipe and filter change. But You know that.
My question is for any info on tune pipes thx
I tried selling this motor a while back and no luck, so I am just going to build this and document the progress in this thread. This motor is a hemi bottom end with a non hemi clone 18CC head:
ARC +.040 rod
Hemi flat top piston milled .005
pop up is +.015(above deck)
Will be using a .045...
Hello all,
Im wondering if any one has some advice.
I Have a few options here but I would like to ditch the jack shaft and install a cvt on it, with this I was wondering if you guys had any recommendations on the rear sprocket for a good gear ratio pared with the cvt. maybe a 60 tooth...
Hi guys ,
Got some time to play. Like to add a few things to my Duddle bug . I got a stock hemi preidtor and got some time to play around. What would be the first mods to do on her? Any suggestions
The chassis is all back together on Project Baja MB200 GC and time to start the engine. The engine is a non-hemi R210-111 from HF that came with the project and not original to the bike. It looks like brand new out of the box minus the muffler. I ordered the OEM muffler and gasket off the web...
I'm building a motor for a new bike (I don't have it yet, more to come on that one later). Decided to build with the 212 predator (60363) I got with a coupon for $99.00 at HF. It's nothing too wild, but here's the plan so far.
Black Mamba cam 0.275" lift, 26# springs
Bullfrog's pop-up...
I have Less than 30 miles on it. I will trade for a nice straight billet flywheel for a Hemi or Sell this for $100 shipped save ya $30 some bucks...... also I have a motorized bicycle so I don't post a lot here. But I get all my technical info here!
Ultra-Light SFI Certified Billet Aluminum...
im looking to replace the rod in my predator, its a stock hemi. was looking at rods, what kind of clearence do we have in these engines?
i see they sell a .020 and .040 longer rod, would those work in a stock block/head?
whats longest i can go?
fOR SALE
Domed piston hemi build. All the good stuff. Arc long rod. Wiseco custom machine dome piston .110" dome. Fits inside a stock hemi chamber only. 27/25 stainless valves. 26*springs. Valve job. Slight port n polish. Quad crank bearings. Ambush billet covers custom finned. Raceseng...
Will a Hemi MOD2 camshaft work in a Box Stock clone? I have a MOD2 hemi that a YouTube subscriber sent me. With it fit? That might be a good cam for my project.
Has anyone ever used one of these high compression pistons from bullfrog motorsports in a Hemi predator? According to their website with no other mods it gets you to 11:1 compression. I was thinking it'd be a lot wiser to do this than mill my head to get 11:1. Ole4 reccomended this to me but I...
Just thought I would throw out a couple of tips as I am nearing completion on this project.
1) Use the tins off the Hisun motor, you need the indentation under the cylinder/piston to fit the jackshaft setup.
2) Grab 4- 5/8"x36tpi-3/4" bolts and lockwashers to fit the jackshaft plate back to...
Hi Everyone,
Got a little bit of an arms race going between my brothers and I in regards to our minibikes. I'm looking to add squeeze some more power out of my Hemi Predator (current set up listed below). Does anyone run a hemi predator with a Dyno 308 cam?
Mikuni 22mm carb (130 main, 125...
Hi Everyone,
Got a little bit of an arms race going between my brothers and I in regards to our minibikes. I'm looking to add squeeze some more power out of my Hemi Predator (current set up listed below). Does anyone run a hemi predator with a Dyno 308 cam?
Mikuni 22mm carb (130 main...
hey,
i have a 212 hemi with a few mods done to it but seem like it not performing right.. could it be to much cam?
part list:
no governor
arc .020 rod
arc ultra lite flywheel
isky .310 cam 108LSA
i have tried 26lbs and 37lb springs
flatslide carb
ported head
.010 head gasket
also what do...
Hey guys I worked on another Murray Track 2 today and put a 22mm "chikuni" on it, after disconnecting all the springs and linkages, how do I or what can I reattach the governor arm linkage to so my engine won't blow up???? It may be a simple fix or a dumb question but i can't figure it out...
I am starting a thread on a non hemi predator motor. This engine came off a Kart my nephews kids race on a kart in my backyard. It was a stock Non Predator engine and I never had an interest in it as I find the hemi to be a much better platform for my engine builds. The reason for this is that I...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.