hemi

I have a Predator 212 Hemi. I started looking for a cam thread but didn't find one. What is the progression from stock to wild as far as cams go? Is there a chart that shows lift and duration of all the cams? How much cam you safely run in a stock 212 Hemi? I mean using stock piston, stock...

Hey everyone, first post to the forum, I just recently bought a non hemi predator for my Margay Expert III go kart build. I have a budget of $600-700 for go fast parts, so far I have removed the governor, oil sensor and plugged all the holes. As far as parts go, I have been looking around on a...

Does anyone know of a source for a nice plug and play throttle linkage for a hemi predator with the governor removed I've seen a few but they all say does not fit the hemi.

If I install White 26lb. valve springs do I need different lash caps or do I use the stock ones?

Hey guys give me your thoughts on this build should I go Tecumseh or Predator ? Rebuilt Tecumseh HS40 mostly stock and will stay that way. Or a Predator 212 Hemi head (60363) that will stay governed but maybe some after market parts. OH and I'm a big boy..:anon.sml:.so give me your honest...

who's doing hemi head with big vavles and ported??? who doing good work??

For sale: Black Mamba Sr. Cam. Approximately 1 hour run time since brand new. $50 shipped. This is for the non hemi predator.

Is the Predator 212 the same engine as the Predator 212 hemi?

what is the max lift a hemi head can take without touching the top of the piston relief..... was thinking of getting a .310 cam with some 1.2 rockers and some 26lbs springs those that sounds right for a little drag motor?

Just getting into the minibike Draging world. and just got me a Predator 212cc Hemi i see they have alot of different valves for this head How big of a valve could be installed with out Cutting the vavle seat and doing and mods to the head to make it fit??

Have a predator 212 hemi mild build bsp3 cam intake and header it makes a weird ticking noise idling, I know it's not a knock when I opened it up the rod was tight like it should be motor is basically new it runs very healthy and it did make the noise when I first bought it. I'm thinking valve...

Good morning everybody, long time lurker, first time poster. This weekend I will be building a Predator 212 Hemi for a Motovox MBX10 that was recently given to me, just something to cruise around on. Nothing too extreme. Tomorrow, I'm planning on going to the local shop and buying a Mikumi...

I know for a fact it can handle 140psi compression but I am curious just how far can it go without launching the head like a rocket. I replaced the stock head bolts with steel ones from Tractor Supply for extra support.

The list goes on and on. Billet flywheel Arc .020 over billet rod Flat top piston Isky black mamba jr cam Gx200 push rods Hemi block Clone 14cc milled head ported and polished SS valves Locks and retainers Champion rockers This is a great running engine. $350 plus shipping I...

OK so I'm thinking on building a predator 212hemi to the max. I'd like some help from the experts please. I'd like to remove the governor, replace flywheel, replace valves, springs, cam, rod, even the carb if needed. Or anything else one seems necessary. So my question is which part numbers...

Will adding these rockers increase my torque. If so at what RPM range should I expect more torque. I have done a few mods like installing high flow air filter Robertsons torque tube 18 pound valve springs Billet flywheel rejetting carburetor and removing governor. After hunting season I will...

Getting a 212 hemi,going to remove governor. What rod,fly wheel, valve springs should I get the more I read the more confused I am.

Can someone point out the difference between the Predator Hemi vs. the non-Hemi engine? I'm planning to purchase a 212cc Predator, but would like to know if there's a benefit to one engine over the other. Does the "Hemi" have a hemispherical combustion chamber design similar to a Mopar hemi...

How much horse power can you get out of the HEMI 212? Using premium gas with no bottles or Turbos. Just new rod cam flywheel and carb. Or anything else to get more power out of the HEMI 212. What is the highest HP anyone has gotten?

Does anyone know if the Mike Clements billet roller rockers 1.5:1 ratio rockers (gold colored) work with the predator 212 hemi?