Hey everyone!
I wanted to make this thread with the intention of posting measurements/dimensions of seats used on some old mini bikes. I thought this would be a great reference thread for anyone that is looking to make or recreate a seat since many didn't survive on mini bikes over the years...
Hi, I recently got a shock from motovox , however they no longer give you the needed accessories :sad:
ray traverio has told me the spacers are available but not the axle. Go Karts, Kids Go Carts, Scooters, Beginner Youth ATVS, ATV Trailers, Quads | Family Go Karts has axles and i think...
Hey guys im relatively new around here I've been lurking around for a few years. My bad if this has been asked before but i been wanting to fabricate my childhood lil indian minibike that i had when i was a kid it was one of the small frame 2 piece designs. Can anyone hook me up with the...
This is a super for riding at Winber......
This came in a kit, about 84 inches long. Everything is new, except for the forks and handlebars.
Has about 100 feet on it from rolling it in and out of the garage.
Nips are still on the wide 205/50-10 Kenda rear. Super braking sytem.
Excellent...
I've got these gas tanks just sitting on the shelve, If anyone needs one just let me know and I'll get you a better pic or do any measurements you need... $20.00 shipped.
Pic is coming, I forgot to download it ! :eek:
If anyone could get me some pics/rough measurements of the battery tray area on the early campus bikes that used the fake tank/cowling I would really appreciate it :thumbsup: I have had one in the past and remember how it looked and I think I can get a rough idea off the welds and cut metal...
Looking for the following measurements on Taco 22 Frame (Series 3 wide frame if possible, otherwise earlier) for next replica build... Distance apart of top tubes center to center, distance apart center to center bottom tubes and same for front forks. Much appreciated if anyone can help.
We need to fabricate/replicate:grind: the foot peg mounts as the original ones on our "survivor" bike were cut off by the last owner.:out: If anyone can help with providing some measurements it would be greatly appreciated. Please PM me and we will go from there.
Thank you,
Michael :wink:
I know that the Heald baskets arent available from Ron Kimball anymore. I speak with him frequently. I also know that he doesnt have drawings for them anymore either. Can anyone give me some detailed measurements of one of the baskets and the mounting frame for the back. I am gonna try to fab...
I'm looking for a correct neck decal for a 1966 Lil Indian. It apparently is supposed to look very similar to the engine decals that are available on e-bay, but smaller and with "Detriot" instead of Livonia. Here's a picture of the engine decal.
I'd like to have a reproduction made, but...
I need the measurements of how far the Lil Indian small frame rear fender mount is from the center of the axle hole. (For the six inch wheels, not the four inch!) :thumbsup:
I searched and didnt find this. does anyone have the measurements of the bracket, with bends and the hole cut outs ? I have one on my boonie i just don't feel like tearing it apart to make the measurements ( yea i know im lazy :thumbsup: ) i just picked up another boonie without the bracket and...
Hi. I'd like to install a billet flywheel onto my EX-17 Robin. However, the vendors I've contacted don't have aftermarket 'wheels for it. No one knows if the Honda/clone flywheel will fit any Robin engines.
If someone out there can post specifications on Hondas or clones, I can compare them...
I need the journal diameter and width measurements for an h70 crank if anyone can help me out..
also did they make an h70 with solid state coil?
I bought what was supposed to be a solid state h60 crank off ebay, needless to say it's not an h60... the journal is too small of diameter and...
Recently I purchased a "Minico Trail Jet" frame.
I'm finding it hard to find parts for this thing!!
I was able to find shock bushings, swing arm bushings, axle and swingarm bolts from sourcing Honda parts. I'm hoping the forks are identical because I have a bent lower fork leg.
The Minico...
does anyone have something like this laying around? I need measurements to see what I can adapt to an Azusa Tri-star to fit a brake rotor on the rim with some spacers. This catches my eye since I might be able to drill the holes where I need them even though this is already drilled...
I was wondering if anyone knew the size of the area behind the seat.
I don't know what to call it, but I usually use it as a handle when loading it up or changing directions.
It's a doodle-bug, BD-30.
I'm looking for the size of the inside of the square area.
Thanks.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.