option

Grabbed a DB30 Dirt Bug over the weekend. The handlebars come straight up, straight up from the forks, at the axle, to where they bend for the actual grips... They are perfect, with no bends from wear & tear (abuse), so I'm looking for the most cost effective, yet smartest way to have/make...

Hello, Looking to find a suitable disc brake for my trailbug. The first pic shows an original set up I'd like to mimic, the second pic is my frame that has the factory welded tab mount. Since original caliper set ups are impossible to find is there an alternative someone has used to restore...

http://www.treatland.tv/v/vspfiles/photos/MLM-ROUND-back-cafe-seat-584-2.jpg There's also a square back style, nice price!

I picked up a two seat Marco dingo for my nephew for next to nothing. I've replaced the crap Tecumseh motor with a 212 and added torq-a-verter. Now it's time to deal with the bad wheels and tires. What's my best option? I saw some listed for the rear at 80$ each. Seems steep to me. What are my...

Tonight I was out looking for some of the Tecumseh white paint options listed here on other threads. Not finding any of those options in my 1 horse town :surrender:, I ran across this Rustoleum Appliance epoxy in "Biscuit" white from Lowes and gave it a shot. I know it may not work in the...

I'm not fond of the heavy feel on turns of my ct200u..its tire is a 19x7.00-8.. was thinking of using a 16x6.50-8 turf tire on front part R_8542 in ombw ..says it's a tube tire in spec..do I need a tube? Is it logical to think this would make steering feel better...thanks

So..... Long story short.... I got this ski for my S.O.B trike.... But it does not fit and I don't wanna modify it... After consulting with another member we determined it to be for a alsport trike... Hence the white color with red/blue stripe.. Thanks to Nate, George for there...

What ya think..

heres a interesting tecumseh lighting coil assembly. three coils.....tied together with a connector that attaches it to a full wave rectifier regulator. when i saw the photo online i didnt realize the lower right coil was tied into the setup. aside from the top coil which is 180 degrees...

I am considering selling a Benelli Buzzer that's been sitting in my in-laws basement for the last 40 years (it's always been inside) except for the 341 miles put on it back in 1971. I've looked everywhere to find out what it might be worth without luck. Any ideas or suggestions? My other...

If I were to build a fat tire bike around these tires would it even be remotely rideable? Can't get a pic to post. They are Vendetta 26x16-12 with a moderately squared shoulder made for the small amphibious 6x6s and similar. Obviously this bike would be used primarily off road, but I...

What's the main differences between the animal, animal. Local option 206, and M series?

though I like minibikes this time the question is for a mower. So is the only option for a warped fuel tank the roll pin and nylon washer(B&S repair part) or replacing the tank, are there any other options

I see some people have a "signature" that shows up whenever they post, however, I'm not sure where to edit my signature???? Heck I don't even see having a signature as an option, but clearly it is because people have them... halp! :confused: Mike

In need of a float carb option for a flathead briggs 5 horse. PM me or something!!!! thank you!!!

Found a super cheap option for a Drag Parachute ! 56" in size, ( 4'8" ) may need to install a longer led? Far better cry from $120 - $500.00 Parachutes. At this Price, I could buy 3 4 Color 56" Speed Resistance Parachute Chute Football Running Exercise Training | eBay

Hey guys, I have been waiting for OldMiniBikes to get the db30 brake rotor back in stock but it seems like it never does, so I went on ebay and say this... MTB Bike Bicycle Cycling Stainless 7" Disc Brake Rotors With 6 Bolts 160mm 180mm | eBay Can anyone tell me if that would be able to substitute...

I just bought a new predator 212 at harbor freight. Its the old style valve cover which I was surprised. I started to replace the stock 22cc head with my aftermarket 14cc stock head but the 22cc head has 27mm intake and 25 exhaust valves at 5mm in diameter. Also, it has automotive retainer and...

creekbed crossing polaris 800 with tracks - YouTube

I did this the day before I got notice that the hydraulic brakes were back in stock:doah::grind::hack: Works great decreased the life of my rear tire significantly, I can lock the tire. Good solid feel on the lever not mushy like the original cut my stopping distance by 50% or...