plate

My doodlebug has 8 slots on motor plate. Will a predator fit those bolt patterns? or do i need a special motor plate? I saw something about motor plates not working on 8 slot stock plates. Can anyone shine some light on what my options are? Thank you.

My Tecumseh H50 65242H is running rough and I found a good read on checking the coils. Also I want to find out more about the core plate group. My plates seem to have spread apart or fanned out a little and I'm wondering if there is a way to repair it or if it has a huge impact on the firing. My...

So I am building what should be a 69' BC1400. The fork plate has the serial number stamped on the round Bonanza tag, there is no tag or rivet holes on the front of the engine plate that I see should be there. Did all Bonanzas have an engine plate ID tag riveted on there? Were there other...

Who has an original Trail Blazer decal that can measure it for me. Also, I would like a picture of it with a tape measure next to it. The one I bought off ebay is way too tall and I would guess it should be the same as a Trail Horse decal. My Trail Horse decal measures out to about 4 3/4 inches...

Hawg Ty with ARC Racing throttle plate on Predator

Looking for a switchplate, clutch and chain guards for a VT-7. Looking for the old style sheetmetal guards. If anyone can give me the dimensions, I can make them. Any help is appreciated.

ok just recieved the adapter plate to put a predator on a doodle bug, gen 1. slots in plate measure 80mm centerline original slots on bike 62mm....ooops! will call on monday, anyone else come across this? mark

I just bought a ARC Top Plate from OldMiniBikes. my question is, do you have to remove the governor to use this? Is there any way around just removing the lever? They didn't mention anything about that. I am putting the Red Clone on my sons go kart and had to move the relocate the gas tank. thx.. mike

I got a db30 an going to put in 5hp Briggs do i got to use that per engine swap, plate an if so why is there a sprocket to run bigger chain an where, can I get one thanks

Custom Speedway mini bike License Plate for your show bike or use it to dress up your rider. I had several of these made up for my Speedway bikes. The aluminum plate measures 6 1/2"L x 3 1/4"W. The vinyl logo is modeled after a Speedway patch I saw in an old brochure I have. PRICE $40

Like the title says, does anybody have a picture of the hot rod minibikes engine swap plate on their DB30 they could post? :shrug: I'd really appreciate it. I bought one of the OldMiniBikes ones and I'm feeling like an idiot because I can't figure out exactly how it goes. :doah: It should bolt...

Anyone know of a commercial product that allows adjustment of the engine's position both forward / backward and side to side? Has anyone built a custom one yet? I’ve been playing around with design ideas, but don’t want to reinvent the wheel if it already exists.

Anyone know where I can get one?

I was wondering if anybody out there has a PMR DB30 motor mount plate kicking around that they aren't using? :shrug: If not I'll get a new one but it will cost me $80 shipped, and OldMiniBikes Warehouse is out of stock at the moment. Thanks guys. :thumbsup:

Here is just the brake backing plate for a Bonanza. $25.00 shipped. Paypal an cash only, Lower 48 states only.

Was looking for a universal engine mount bracket. Feel free to PM me. Thanks Jay

Eric has fabbed up a polyurythanes plate he hopes will provide some decrease in vibrations after mounting between the engine and the frame. He asked for a volunteer to try this out and report back on the findings. The thread that began this can be found here...

Engine swap plate for the Db. Looking for a used one in good condition with all hardware. I want to trade, but have cash.

In general, is 1/8" steel thick enough? Im setting up a 6.5 clone > TC > to jackshaft. It seems a little flexy when I set the engine on it but I thought maybe I could re-enforce the bottom with 2-3 steel ribs of angle iron or tube. Or should I just go up to 1/4"... (I already bought the 1/8"...

I am looking for a rupp USA plate like this one. The condition can be rough like this one. Thanks