Looking for a set of nos or real nice red plastic speedway fork plugs. I thought I had a nice set but everyone I have seems to have some damage. I will trade a used set and money if you need a replacement. I will pay top dollar. Pm or email aaronfriedl@yahoo.com
I am wanting to know the importance of removing and replacing the welch plugs on the 631588 diaphragm carburetor during a rebuild. The engine went through a flood and I did a complete tear down of the entire engine to clean, dry old and fresh lube approximately 1 week after the flood to salvage...
Is there anybody out there that has some front shock springs, upper and lower plugs for a '67 Rupp Continental?
I have exhausted all of the parts outlets I know of and found the lower plug only. (Blackwidow Motorsports)
No swap meets at all in my area. I thought OldMiniBikes would have a parts swap...
I know this has probably been brought up 100's of times, but what spark plug do you use in your Briggs 5hp flathead ? Heres what I'm starting out with.
I also have a Autolite 411 coming in today.
Brand New Old Stock! No more messing around with scratched, chipped, stripped, painted over caps.
$10 bucks for two, plus $3 bucks to ship. Paypal only please.
I have a "few" of these...
Hey Fellas, I'm missing a couple of bits for this Tecumseh I'm rebuilding. I could use a couple of screws like the one pictured for the plastic tank. I also need two drain plugs with the square end so I can remove the extension that is shown in the pic. Please, let me know if you have a donor...
Do the Flexo front springs come out of the forks like the bonanza springs.:out: I know they are a bit rusty and it took me 2 days to get the screw's out. Springs & plugs removable.:out: Thank you.
For those that would like to install a drain plug with a magnet and find them to expensive do as I did. I used neo magnets from Ebay(like item 190941084399) and drilled a recess hole in my motors drain plugs and set a magnet in it. I don't use any adhesive as the magnet is so strong it doesn't...
For those that would like to install a drain plug with a magnet and find them to expensive do as I did. I used neo magnets from Ebay(like item 190941084399) and drilled a recess hole in my motors drain plugs and set a magnet in it. I don't use any adhesive as the magnet is so strong it doesn't...
What spark plugs are you Keystone TAS 2-stroke owners using for that motor? My bike has a AC CS45 but I am wondering if there is maybe a NGK equivalent?
Sent from my iPhone using Tapatalk
I have a MB165 with the 5.5 Jiang Dong engine. It just destroys plugs. I have to replace it every 5-10 hours or so. Any thoughts? I'm going to put a different coil on it to see if that will help.
AutoLite AR3910X ~ Racing "X" Series Spark Plug - eBay (item 400173756341 end time Mar-16-11 09:53:23 PDT)
i've been looking lately but haven't had much luck and saw these on Ebay. not a bad price so i bought a couple. figure i'd throw it out there since OldMiniBikes is out of stock for now and ARC...
Why do my spark plugs keep gapping down after a few hours? I always gap to .030 and when my bikes starts acting funny, I pull the plug off and sure enough its at .020-.025. Maybe when im gapping, im gapping the arm part instead of the electrode, causing it to keep warping.. Anybody have any...
How many welch plugs are on a small 2 pc. flojet? Between the choke and the main needle I have a spot on my carb for a welch plug I think. It might also be a drain hole or a breather hole possibly.
I believe the only welch plug on these carbs is on the end of the tube for removal of the choke...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.