seal

Hello everyone, I ordered a new carburetor a little while back for my hs40 engine because for the price of all the replacement and cleaning I could just get a new carb instead. I ordered the one that said fits the hs40 engine and replaces part #632113a (I could not find my part number prior to...

Where can I get an oil seal for an HS50 with a ball bearing side cover? Engine # is: HS50-67124D. Most of the illustrated parts lists I have found don't show it.

looking for a new seal part number 692001 (555121) rubber seal, not the foam ones..

In my gx200 build I'm going with stock valve train with 1.3 rockers and 18lb springs from agk. Do I yank the intake valve seal to gain some installed height and prevent coil bind? Also I read that only the 160s have the seal...Truth? Are they important to have? Thanks!

On a H70 non-bearing side cover what is the trick to put the oil seal in? Do you have to press it in in order for it to crush and expand out? I removed the old one and the new one just slides right in the side cover? They are the same size seal. All help is appreciated.

I am having trouble getting my Moto Skeeter to smooth out, now granted it is from 1972, but I have had the carb apart several times and cleaned it quite well. However I am still ideling fast and the mixture screw has no effect on how it runs, I can close it ,or take it out and it makes no...

I'm restoring a '72 Arctic Cat Prowler with Sachs 47cc engine. It sat in my garage for nearly 30 years unused but I put plenty of miles on it back in the day. I am trying to avoid a full rebuild of the engine. Piston and rings were new back when I stored it and a compression test showed...

I need to replace the crank seal on the flywheel side. I don't mind having to remove the flywheel, but I would like to remove the old seal and put in the new one without removing the crankshaft. Is there a good way to do this?

Does anyone know the part number for the oil seals for a hm80 1" shaft? I need to order 2 new ones this weekend and I am 2 hrs away from home for the weekend and can't look at my engine.

Hello, Anyone have the Tecumseh PTO seal number for the side cover that has the PTO bearing option? Can't seem to find the PN on the Tecumseh parts sites. Any help would be appreciated. Regards, Joe

I got an old fuel tank, probably from a mower or tiller, from a local man who sells small engine parts and mowers ect. It cost me next to to nothing, but the seal around the cap is shot, so the tank leaks. What could I make a new seal out of which is cheap and can endure exposure to petrol? I...

I turned 55 my last birthday. In my opinion, I've seen a good bit in my lifetime. Now though, I think I can safely say that I have seen it all. A company called "Hero Builders" has made a doll called- ‘Rambama’ SEAL Team 6 action figure. Please don't misunderstand my disapproval of Obama, I...

If clearance permits, does anyone use the valve stem seal after hopping up their motor. I left mine out, but there is room for it. Pete

i hope this is the right area to post if not sorry. i just picked up a continental ac6 1 1/2 hp early 50's for sure vintage, made in detroit for sure american. trying to be clear because SOME guys seem to scold you like a school boy if you post in the wrong area! ok here goes ,info on this is...

on the clone heads there is a little cap thing that i read i some sort of seal against oil. but it only comes on the intake side. should i add one to the exhaust side as well so the spring tension is even? or is there a reason that they didnt put one on the exhaust side? i have an extra one and...

I have a leak in my head, when the motor revs carbon shoots out of like a 1" long gap that isn't sealing. What should I do?

:( im hoping to have more luck here. ive bought two so far. 1 from milford power and the other from ebay. both saying that it would fit, but it didnt. anyway i was wondering if anyone had a oil seal GUARANTEED to fit a Tecumseh h35 -GC-

Who knows of a web site that deals in these they were used on 1/4 midgets simplex and others

I've got oil spewing out from around the crank-shaft clutch side area and from "searching" I guess I need to change the oil seal (got one on order). I've never done this before and want to find things out before I open this thing up. Is there anything I should look out for while doing this...