threads

I'm going to install an end bolt in a 3hp Briggs to retain the clutch...The existing hole is not tapped... I'm seeing online that 5/16 x 24 is standard for clones...Any suggestions for the smaller 3hp crank....What size drill bit for the correct tap size.. Building a standard Taco 22...... 60's...

Like anything with the word "Game" in it, and a couple others .... Is there a way to opt out?!?

Is there and old school Only minbike thread or forum area? By Old School only I'm taking about minibikes like a Lil Indian, Ruttman etc with small tires, NO suspensions, No jack shafts, no 2 speed trannies etc. Just a frame, flat head Briggs, Tecumseh, one clutch, one chain and the typical...

Is there a way to find passed Build Off Threads, I'm not having any luck.

I just painted my tank and I have a new petcock, what do you use to seal the threads? I'm sure Teflon tape is wrong:)

anyone know what it would be? I bought replacement nylon bushings. They seem to have a thread OD of 1.020 ".....but a pitch of 1.0 mm

It seems like everytime that I try to look at a post...I get knocked off to Dragon Bites...or something like that. Like the site is down...Is it just on my end ?:blink:

If anyone that did not finish their build wants their threads moved over to project logs so they can finish it, let me know soon.

Hello all, I noticed in a lot of the build threads there is always a picture of a dinner fork. Either plastic or metal. What does that mean? Also, what do the abbreviations in the build off threads like JFF and MTTW etc... mean? Thanks, Shawn

There were some threads that were visible, but not necessarily searchable even through members recent posts. This is fixed now and will slowly be working on some of the other quirks the site has and then onto larger projects for it. :thumbsup:

What do you do in the case an engine has no threads for the clutch bolt? I was looking at an older 3hp tecumseh but it has no threads to hold clutch. Any advice would be greatly appreciated. Thanks

saw this being done in other threads and thought i would give it a try. it didn't work too well. i used a spark plug to chuck the head, not the best idea. the washer must be moving around: i might try removing the washer or turning a piece with the threads on it. my little lathe has...

Need adapter that gives you threads for mufflers on HS50. Would take 2 if u had them. I think the part is 730165 but hard to tell from drawing if there are threads. Cant see what else that part would be for...

I am looking to get a tap and dye set so I can fix the threads on my crank shaft. They're buggered up on the flywheel bolt threads. What size dye do I need, and can you recommend a good brand? I'm new to the rebuilding engines game but wanted to get some good tools so I could do it and do it...

the boxes where you could click to see your threads and your posts?

Started on the black widow. Everything was good until I opened the carb. Need the top part of the carb where the filter is located. The filter slides over the threads and a cap holds everything in place. The threads are gone ugh. Rest of the carb looked ok. Thanks dave

I have the tank, I need the metal cap. This one is rusted through. Tank is fair... Cap is the one on the tank, threads measure 1 3/4" outside. Sorry I don't have a closer pic. Interested in cap or cap and metal tank. 3hp Briggs. Thanks for looking!

I just painted a bunch of stuff from fenders, gas tanks to full frames. I used duplicolor engine enamel with a self etching primer as it had been stripped bare. Everything came great. Now I realize I need to order Duplicolor clear coat. I had thought any clear coat would work but after reading...

I picked this exhaust up recently to use on another bike but it won't fit. Originally was a Heald Super Bronc. Flexible stainless steel tubing included. Nice, solid, usable condition. Both bosses have good threads. Asking $130 shipped. PayPal, USPS money order, or cash.

I don't want to sound like an idiot but I will anyways. Whats the thread size and pitch of the pto side on a Tecumseh h60?