6.5 horsepower block with - these modifications done by an official small engines experiment
"Killer engine built by 125CCRAZY"308 cam
new honda flat top piston
file fit rings
arc flywheel
8mm plug wire
champion rockers
chr push rods
raceseng guide plate
new intake
26mm mikuni
28.5mm int 25mm...
Wanted: Stellar Compact Deluxe mini bike complete. Do not want junk or your "Priceless" mini! Top $
Have no problem paying Top dollar for one but must be clean. Be Realistic please. .
NO JUNK.
Thank you in advance!
OldMiniBikes and it's members Rock!!
OK, what setting on my private messages do I need to change to what in order to read PMs normally ? They are being displayed on top of each other, the latest one getting thinner and thinner. Thank All. :confused::confused::confused::confused:
I have for sale a Honda GX160 block, Side Cover and Flat Top piston and rod. Low oil sensor, and Governor holes plugged. Bore has a fresh cross hatch. Bought the block and wont be using it. I do not have the rings for the piston, but is a Z4M piston. Block has been clearanced at the bottom of...
Hey guys im new to the form gonna be doing a full engine build on either a 5.5 or a 6.5 honda motor i have looking for some imput if anyone has built oneband would like to share the specs and speed it did i would appreciate it alot thanks for the help in advance :)
Hi guys. my mini has a briggs WF engine with some minor mods, (cam is an ANmod01, better springs and a tm24 carb) on gas. I also use a tav2. My top speed in the 1/8mi was 60mph. I want to put larger valves and increase compression but for now I would like to know how it stacks up against...
I may have started this thread in the wrong section before.
So I have a 6.50 Chipper Shredder Vac by Troy-Bilt that I did a repair of the bottom oil seal.
Also replaced the Magneto due to no spark after I reassembled the entire machine it was still leaking oil from somewhere under the...
I believe I pulled the bone head play of the season...
Will oil from a blown top seal, short out the coil of my
6.5 Briggs & Stratton Vertical shaft small engine?
brand new take off hemi flat top $20 shipped
also have a hemi block side cover crank and cam cheap if some one wants it :thumbsup: just have too much laying around and projects to finish
I just finished swapping a predator in with a Chinese torque converter and a 60t sprocket. I seem to only hit about 35mph. I weigh under 200lbs. I removed all components of the governor when I installed the new flywheel. Other than that engine is completely stock. I was thinking I would be...
I just bought a Lil'Indian Sabre...probably be a while til it's in my possession, but I know it will need the top plate that the handlebars slide in to. If you have one, please PM me. I have stuff to trade or PayPal. thank you
Looking for a Briggs 5hp round top recoil cover or covers in good shape.. a small ding or two isn't an issue as long as they are not rusted out, pitted real bad or twisted out of shape.. I don't need the recoil pulley or spring assembly... years are not important...
I have a h35 that seems to run out of pulling power once it reaches like 10-15mph. It feels like it just dies and then once speed comes down it has power again. Can't seem to keep it pulling. Any ideas? Thanks
I was just playing around with one of the top speed calculators and I bought a torque converter kit for my 212 predator I put in a go kart which is strictly got off road use, and the kit came with a 10 tooth and a 12 tooth sprocket, my axle has a 60 tooth on it and I went with the 10 tooth for...
Looking for the following parts to complete a TACO 55 WITH HOT SAUCE OR A TACO 99 fitted with a WB 820 engine:
1) The original long round domed ends gas tank with cap. Petcock also if you have one.
2) The correct original air filter used on the WB 820 for these 55 and 99 models.
3) The...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.