top

used seat one little ding in the top $25 shipped :thumbsup:

Does anyone have any YFM80 top end parts laying around? This is the little quad that I picked up for the granddaughter a few years ago. I pulled it out, fixed the flat tire, and got it running. Was just putting around and she stalled out. After pulling the head due to no compression, I found...

So after removing the molasses that the previous owner used for gas I'm putting the carb back together and have a quick question: As the carb sits on the bike, does the gasket go on top of the diaphram? Meaning the sequence from bottom to top goes: bottom plate, diaphram ,gasket, carb body...

Set of forks, unknown origin that aren't perfect but still usable. They are 20 inches long x 5.5 inches between the plates and 4 inches between the fork bottoms. There is plenty of room to enlarge the fork bottoms and top plates to 5/8 axle bolts. The good: the springs are free and work as they...

Hey guys, new to the forums after being bit hard by the mini bike bug. Gotta have one! Someone offered me this old Alexander Reynolds for $60. Bent forks and not running. Can't seem to find any comparable bikes online. Obviously someone has messed with the seat, but apart from that it looks...

I'm only a few steps from completing my Doodle Bully build, with only rims, paint and lights to go. I took the time to get it running exactly how I want with tons of low and top end.:thumbsup:

Thanks for stopping by! I need a good core carburetor for a Briggs 5HP. I need the old style, pull choke carb that mounts on top of the tank. let me know what ya got!

What is the process for disassembling the forks in arctic cat minis? I have a 72 prowler and the forks are very tight. I want to disassemble them and possibly put new liners in. I know there is a spring in there and one bolt at the top of the tube but I'm not sure how that comes apart. A buddy...

I am wondering on the best way to make a tank that sits on top of the frame like a Heald Super Bronc. I was going to cover the frame with plastic then use "stuff it" expanding foam insulation to make a mold that can be trimmed down. Then make a seperate top half and fiberglass together. Then...

There is gonna be a fun Barn Burner this weekend. (Jan 17-18) IV LEAGUE FLAT TRACK is bringing Flat Track back to San Diego. Many CLASSES, from Groms on 50cc mini bikes, -all the way up to- top National Open Pros ! Even "PULL-STarT MiNi's" !!!:scared: (mini bike class only $15...

Hi All, I am using a Tecumseh hs5 motor on a Rupp cont. with a 12 tooth/35 chain motor clutch. I have a 60 tooth/35 chain rear sprocket on a 530/450 -6"in. tire/rear wheel . I have nice original 5/8"in.jack-shaft with no sprockets on it.I want to use the jack-shaft on it but I am very confused...

I have a late 60's Briggs 3hp engine. Im trying to put a newer style carb on it. Right now it has a carb that sits op top of the gas tank and is bolted directly to it. I don't like that style so I'm looking to buy one that doesn't sit on top. I will try to post a pic of what I have and what I...

what all does it take to do this? probably going throw this crank in with a std length billet rod, with flat top piston. will I have to mill the piston down? looked all over the site and couldn't find anything

Looking for $900 or best offer shipped NO CLUTCH -predator 212 block and crank (gov and low oil removed and sealed) -arc billet rod -wiseco flat top piston -arc light billet flywheel no fins but have plastic fan if needed -mikuni 28mm slide carb methanol and manifold (ran gas before needs...

I know a lot of you guys probably could use this sort of thing to deter curious people from snooping around. They're obviously not as effective as a real security system, but it's a good second place. These sell for about $7 on Amazon.com *** There are two mounts on these cameras, one on the...

Glad we are up and running , I'm in detox but think I'll make it ? Anyways where is our little post and thread guide in the top right corner ?? I guess I'm lost ?, PM's too ?

The new style thin ring Tier 3 piston and some clone pistons GX 160 left, Gx200 center and the new piston right