I have a Huskee Hill Climber made in Tiawan. I need new fork tube bushings.
The need to fit in a 21/32" head tube and have a 1/2" diameter hole for the bolt.
They are about an inch long and the flange is about one inch across.
Hello everyone just getting back into this AWESOME hobby from years ago when I actually fit a little better on one!! I am looking for a few parts to go on an Tecumseh 3-4 hp model 143-614132 that is an original on a sears mini bike I just picked up.
1) White gas tank...
Just a mini project for my tubing bender (JD2 model 32)... its going to be hyd. but for now going to bend everything manually...
the way my garage is setup and constantly switching between projects, I dont have room to mount the bender in a fixed location... i decided to make a rolling...
Might be a dumb question....I think I already know the answer, but hopefully some of you more experienced guys know the answer for sure. My six inch rear wheel has split rims (if that is the right term) two sides that bolt together. Can you use a tubeless tire on them? I feel like there...
Guys....I just bought 2 new pickup tubes for my B&S Pulsa Jet Carburetor that goes on the 1976 5 hp flathead. I know that the short one just screws into the carburetor, but the longer one somehow fits over the metal tube and then uses a new ring? clamp? to hold it in place. I just tried slipping...
so i found an old thread about the 6900z bearing. they suggested that it was better to get a 6900rs for the rubber seal. I'm still not sure what bearing i need after going to the mob wear house. there is a ton of bearing on there. noting is specific?
what bearing or part number do i need?
when using the jet kit from OldMiniBikes was i suppose to turn town the idle screw cause when i gave it full choke without hitting the throttle it took off from me causing me to crash into a garage nd if anybody has pics of predator engines with throttle hook ups plz post pics or is a mikuni a better...
I bought an airfilter kit for my new Coleman 196cc minibike.. where does the crankcase vent tube go when you install the new filter kit??
I don't want to leave it open and dangling to suck in dust..
Suggestions on a CHEAP filter (aka mini KN knockoff maybe) for it maybe??
1 Carlisle Indian Head tire and tube 4.10/3.50-4. Tire has some cracking. Not safe to use on a driver but, good for a display or to finish off a barn find.
$10.00 + shipping
I'm building the bike below in the Projects Forum. I have a question about securing the forks in the steering tube. The steering tube is about 6" long 1.25" OD and 1" ID. Right now I just have 2 washers tacked in place (on top and bottom on steering tube) to shim the 1/4" bolt that goes down...
Hello all. I'm new to the site, new to mini bikes and new to working on any kind of motor. Recently purchased a motovox mbx10, replaced the motor with a predator 212, and added a header, intake kit and jets. The problem I'm having is removing the stock emulsion tube. I've removed the stock jet...
I just ordered a a/f kit, jet kit, spark plug and throttle plate for my Red Clone from OldMiniBikes. I have a header for it. My question is what do I do with the breather tube off of the v/c?
I'd like to thank everyone on here first for all the incredible help. I don't have much to offer but am thankful for all the help!
On my mitsubishi 6hp there is a hose that goes directly from th valve housing to the airbox right before the carb. I am assuming that it take atomized oil and...
hi guys, for those who fabricate their own axle tubes and hubs, what size tube are you using in order to slip a standard 5/8 bearing 1 3/8 OD? I was wondering if I use this "1-5/8 OD x .120 wall x 1.385 ID" if there would be too much slop for the bearing.
I am trying to avoid using a live...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.