212cc

This is my first mini bike build. I finished it and took it to a local car show, Hippie Killer, in Perris California. They used it for a photo shoot.

This is my first mini bike build. I finished it and took it to a local car show, Hippie Killer, in Perris California. They used it for a photo shoot.

This is my first mini bike build. I finished it and took it to a local car show, Hippie Killer, in Perris California. They used it for a photo shoot.

This is my first mini bike build. I finished it and took it to a local car show, Hippie Killer, in Perris California. They used it for a photo shoot.

This is my first mini bike build. I finished it and took it to a local car show, Hippie Killer, in Perris California. They used it for a photo shoot.

My brother wants me to build him a motor. He just picked up a new H F non hemi 212cc. He sent me a list of the parts he wants- billet flywheel , black mamba cam .275 lift with .246 duration 26 lb springs , arc billit rod 3.595" x .490 , flat top piston +.020 , will this all work with the stock...

Hi everyone! I just took apart my Predator 212cc engine and removed the governor, then put it all back together. Then I replaced the throttle on my mini bike. Now, the engine won't start! I currently have the throttle wire leading to the throttle arm, which I still have connected...

Hi everyone! I have a Baja Warrior with a Predator 212cc engine. I currently have it all taken apart to repaint, and I decided to remove the governor while I was at it. (And don't worry, I already ordered a new flywheel and rod.) I took apart the engine two days ago, and every since I've been...

I bought the stage 1 kit for it, so air filter and jet were replaced. The little butterfly mechanism on the carb doesn't snap shut when I let off the throttle. I disconnected the throttle line to make sure it wasn't causing it to hold the throttle open, so that's not the issue. Any ideas?

I have a non-hemi Predator 212cc on an old manco quicksilver go-kart chassis, it's been in my dad's shed since 2012 or '13, can't remember. The reason being a worn jackshaft sprocket and a driver unit that stuck open and wore belts out in a matter of hours, and no time to mess with it back then...

What is the best over all cam on the market that i wont spend too much money on. I was looking at the CM grind cam but not sure. Thanks

MTD trail flite 212cc dyno cam 18lbs springs .032 jet header air filter DB30R gc160 header

I recently picked up a hi comp 18cc head from OldMiniBikes, and when I went to swap mt valves they were too small for the guides. You can knock em back and forth and im pretty sure theres not supposed to be any play here?

Figure out if you have a Hemi Predator 212cc or not by looking at the valve covers

Figure out if you have a Hemi Predator 212cc or not by looking at the valve covers

Hello all. I picked up a new 212cc Predator engine recently to run in an old Mini Bike of mine. I can ride it for about 5-8 Minutes with a lot of power, But after that It loses a lot of power. It seems when the engine gets Hot. I put new Oil, New gas, Its a new engine, New clutch, Air...

I am really confused about where and which gasket kit to buy for the Predator 212cc Hemi. Can some one tell me what to buy? I want to have some on hand. Thanks guys!

Planning to swap one of my 196cc Baha engine with a 212cc Predator. Will I have to change the clutch, or will the old one fit? Anything else I need to worry about? Thanks.

Grayson County Texas here. I have been searching for a while for any mini bike to fix up. Stopped in an old mower repair station in Paris Texas one afternoon. Asked if by chance he had any older minis around. He answered NO but I have an old Manco for $50.00. Bought this Big Cat and a go...

Just posting up to say hey and drop off a pic of my DB. Will be reading and asking alot of questions. This is my first mini bike and I'm already looking at getting another on locally! Anyway...here is my current project. Has a running 97cc in it. But i have a 212cc on the work bench ready for...