bolt

i'm installing a 97 CC Baja on a Cat 250 I think and need to turn the clutch around. I removed the snap ring, but it looks like the bolt is broken off. I have the clutch off but can't get the rest off the bolt. Tried heat. Now I have nothing left to grab on to. What's next (drill and tap)

Hey guys. Just introducing myself, I'm a proud and first time owner of a Coleman CT200U. Back in the day I was one of those kids who never got cool stuff like this. I was so envious of the other kids in the neighborhood scooting along on their gopeds, mopeds, and mini bikes while I was using my...

Im doing a 73 briggs 5hp for the build off an I got a question I know I need the 1" 5/16 bolt to hold clutch on engine only problem is my crankshaft isn't tapped with thread for a bolt can I just use the set screws on the max torque clutch to hold in place or do I got to get the crank drilled an...

Selling these forks from a project bike that wasn't finished. The spacing between the plates is just over 5 1/2 inches and uses a 5/8 axle bolt. They will work on different bikes and give them an Old School look. Asking $125.00 shipped from N.Y. 13032 Shock not included. Thanks

Hello, the previous owner of my gx140 motor disconnected the governor linkage and the stud is only sticking about the case about 1/8". It sounds like it's hitting something inside. What would be the easiest fix for this? I was thinking of tacking a bolt on it to pull it up and drilling a cotter...

I'm looking for a Taylor muffler or similar muffler that would work for my engine. I'll try to get the bolt pattern up later. Sausage muffler works too. Thanks.

I am in need of a 4 bolt front wheel hub with 2 inch spacing for a steel two piece wheel. I am not picky if it's new or used and it doesn't need to have bearings, just the mount is okay. Thanks for the help!

Anybody know where I can find torque specs for the bolt circles around the crank shaft? I will be mounting a TAV and wnat to snug it correctly.

I have one now, but the throttle shaft has way too much play in it! I need the older version from the late 60's with the small bolt pattern, and the smaller tank to carb gasket...if that make sense. I already have the deep tank for it. Let me know what you have!

Hello lookin for a factory jack shaft bracket for my boonie. Please pm me and let me know what you got… THANKS!!!!!!!!

What's side cover bolt spacing to mount tav? On side cover? At work and drawing a blank. Got it. 2.5 inches

HELP I tired a 1/4 x20 but they do not fitIt's a DB30 Can they be metric? The chain guard fell off but I found it but not the bolts.

How tight should the rear nut be that holds the driven onto the shaft? Just hand tight?

I am going to put on a new exhaust pipe on my H60 and I noticed that there are threads in the exhaust port. I had a couple pipe fitting at my house so I tried and it screwed right in. Is there any advantage or disadvantage to running a strait pipe screwed in vs. a bolt on strait pipe?

Doing a Briggs swap on my doodlebug and have been waiting on a clutch to show up. Well now its here and I've discovered my crankshaft isn't threaded for an end bolt. I figure the chain will keep the clutch centered and am using both the set screws at the moment that came with. Just wondering if...

looking for a sprocket and/or a brake drum for the TH 3 bolt steel wheel bolt pattern..

could someone tell me the crank bolt size for the predator? apparently my bolt came out somehow, on my predator that is on my db30, and i cant find it. i went to finally start it after sitting all winter, and my throttle was stuck or something, and the bike was possesed for a short time, till i...

Just bought a replacement air Cleaner with filter but I'm missing the bolt that screws into the carb. This is an older Briggs 2hp engine. It has the straight carb with tank attached. What size bolt is used to hold down air cleaner housing?

Does anybody know...is the 4 bolt pattern for a Tecumseh and Briggs EXACTLYthe same...? Talking like an early 70's Tec 5hp vs a Briggs 5HP. Are small block and big block all the same ? .

Hey Guys, I Was Wondering On How to Take the carburetor Bolts Off So that I could Put Shorter Bolts To Mount a Tillotson Carb, Is Their Any videos On How Too... Thanks:scooter: