briggs

i know i posted a link in the pass on this,but i thought it would be cool to show a up date on this custom built 4 cylinder briggs.......:thumbsup: https://www.youtube.com/watch?v=-24ScVo_TxM

like new Briggs & Stratton 3.5 hp motor (Flathead). only 3hrs of use. $125.00 + 25 shipping we put a predator in, took out super nice Briggs 3.5hp motor.

Is there a good color match for the briggs copper color in a spray can?

Saw this this morning--http://www.ebay.com/itm/Lot-of-Briggs-Stratton-3-5-hp-Short-Block-Cart-Mower-Motor-Piston-CrankShaft-/262435985635?hash=item3d1a6758e3:g:1nsAAOSwPc9Wu~iO

Ya say it isn't so? Edelbrock never made a head for the Raptor/5HP engines! That is correct! But as the enterprising stud that I am, I have made this all possible! I have taken the Blockzilla 1 head and had it machined to fit on a Briggs Raptor! This is fresh from the machine shop! These are a...

Ok so I followed everyone inputs on this 5 HP Briggs. My brother took it to his shop. He machined the bore and inserted a fresh cast iron sleeve. He put a nice cross hatch pattern on the sleeve. He decked the mating surfaces on the block and the head. I purchased a new head gasket. He polished...

Currently building an Intek to animal spec, already have a Briggs animal rod on the way soon to get the stock animal flywheel. Does stock intek coil have a limiter built in ? Will I even be able to use it for the animal flywheel? Helps appreciated, thanks

Title says it all, cash in hand

1963 3HP Briggs, I'm not sure if it runs. Carb and tank are there but pretty worn. It does spin freely. No ignition coil. Serial number is hard to read but its close to this: 801?2 014101 6310243 $20 or best offer + shipping Located in Rochester, NY. click for bigger pics...

For sale 12:1CR briggs 305, new dual ball bearing block with forged crank, arc rod, dyno 308 BS cam, oversized SS valves with dual springs, CM pushrods, ARC adj flywheel and OKO carb. All new except head which was worked by JRPW. Never been fired $1000 firm. I can text or email pics.

if anyone would need info on a engine I may just have the answer for it in these monsters. Just let me know and I'll do the best to get you the info you need.

What clutches are you guys using when drag racing these engines? Currently I'm using a tav2 and I don't seem to reach the power band for the engine even after a few tricks to the tav. I can do 330ft at 50mph/7300rpm and only 60/7950 rpm in the 660ft.

Briggs blocks for sale, including one ported/modded/stroke clearanced, one mostly complete short block (appears to be NOS), and one partial short block (used and disassembled). No idea of the specs of the modded block, but it appears to be based upon a dual-bearing engine; stroker clearanced...

I need to repair the valve guides on a 5hp briggs flathead but I have never repaired valve guides before and do not have the tooling. It looks like there are several options out there. The most expensive and easiest looking to use is the EZ bore kit. I found it here: Valve Guide...

Hit me up with a PM if you have one you wanna part with and this needs to have the 4 accessory holes thanks and Good Day :biggrin:.

I'm building a mini for a 6 year old. I only want the top speed to be around 20 mph. Right now he has an electric mini which tops out at 14 mph so I only want it to be a little faster for now. I will be using a Briggs flat head engine I believe is 3 or 3.5 hp. What's the best way to do this?

Just got this 3hp with a mini. What kind of carb is this? Are they worth rebuilding? Can I switch it to a standard bowl carb if I'm going to use a different gas tank? Thanks.