carbs

Will a carb off a honda motor work on my h35? It bolts right up. It is a kehin, might have the spelling wrong.:shrug:stock off a gc 160.

I have a couple of these CV carbs from a 150cc GY6. New carbs take off parts from defective or damaged Quads. Same as BMI is selling, and I was going to give them away lol. Anyone interested? Might be a be a bolt no rejet required carb based on the size of engine they come from. Any...

Hi there kind of new to this, got questions will a tillotson model hf 334wx fit a honda clone and also is this carb an alky? and are they easy to rebuild, any special tools needed? thanks.

Whats the difference in carbs between 24mm 97cc Carburetor with 24 mm Air Intake for Baja Blitz, Dirt Bug, Doodle Bug, & Racer Mini Bikes (Standard of Japan) and 19mm 97cc Carburetor with 19 mm Intake for Baja Blitz, Dirt Bug, Doodle Bug, & Racer Mini Bikes (Huayi) I just sent for a kit...

does any body know where I can get a parts break down of tecumseh carbs with part numbers for a hs40:shrug:

Im getting a tillotson carb for my clone, and i need to now which venturi size i need. Heres my setup, billet rod, flat top piston, billet flywheel, .308 cam, 14cc big valve head milled .065, cm pushrods, 1.3 rockers, header, and filter. Any info is greatly appreciated. thanks

Hey all, I would like to possibly get a different carb for my engine but have had no luck in finding anything on the net. The snow blower that I got the engine off of said it is a 7 hp Tecumseh, but a small engine guy said that the carb is a one speed carb from a smaller engine, regardless I...

Came off a kz550 insides look pretty clean slides are all shiny an move nicely bike had very low miles for a 81' only 15,013 will seperate but am planning on listing all four on evelbay soon need to make some money here

I have a 3.5hp Briggs I/C motor with bad carb (fuel leaks from everywhere). I found a 2hp Briggs that runs well, could I use the carb from this one on the 3.5hp? (cheaper to buy this 2hp versus new carb for 3.5hp)

Looking for Tillotson alcohol carbs, I would like to find a 314, 341 or a 342, let me know what you have, I would be interested in more than one of the sizes mentioned. Thanks

I been building up a 5hp briggs(raptor block) and the carb runs well for an hour or so then it starves the engine for gas, I have rebuilt the carb several times and it works fine for a while then back to the same old crap.Either I cant rebuild carbs or the briggs pulsa jet is crap. What I want...

HL 355 carbs wanted. PM or email. Thanks

Just signed up.

I have two almost new carbs, both have only had gas in them to start engines and then were removed... The 26mm is a flange mount same as the taper bore mikuni, the 28mm is a vm mikuni spigot mount... Both are dusty and should be hosed off with with brake clean but other than that they are...

Looking for 1 or 2, 3hp or 3.5hp B&S Slide Choke Pulsa Jet Carbs for the standard (deep) fuel tanks. Must be in good condition with good pickup tubes Would prefer non fixed jet. Please contact me via PM. Thanks !!:smile:

i have some extra carbs laying around and i was thinking. after seeing mdbikes twin carb setup and knowing i dont have the head nor the cam nor the funds. why cant i fab up manifold to run twin clone carbs. one carb i think would be my max bored clone carb with a fixed jet and the 2ndcarb would...

STILL looking for complete rebuilable/repairable Tecumseh HS40's and carbs for them. Prefer early Rupp/Speedway spec engines as complete as possible. Have cash or parts to trade like TAV's, gx160's, 5HP IC's, Max Torque clutches, Honda gx parts. All my trading stock is NEW or mint used-NO JUNK...

I found a couple of carbs on ebay that will work great on just about any small engine. Don't really want to post up the link or info, but if anyone is looking for one check on ebay.:thumbsup:

I saw this an smokstak,an old engine forum.To remove the powdery oxidation on a carb,soak it over night in vinegar and it will come out looking like new. I was wondering if any one heard about this or tried it. I have two Tecumseh carbs soaking now I will see how they look after a day or so.