grand

What you see is what you get. MTD frame needs some SERIOUS help/work in the engine plate area. Grand Prix frame has had a plate welded on behind the neck tube, but is otherwise all there except engine. Handlebars also have welded on one side by the mount. $150 takes it all. Please PM me...

We're going to try having another minibike swap meet in Grand Rapids, MI. Location is at the same place ....A1 Small Engines & Repair, 600 Leonard St. NW. Date is June 8, 2014, .Sunday...7am - 3pm. No charge to buy or sell. Space is somewhat limited . Bring your own table if you're...

Looking for a few guys who are brave enough to join us and ride the westside of Grand Rapids, MI. This is a "ride at you own risk of being caught by the police and possibly ticketed or have your mini bike hauled away to the impound" kind of ride. Actually, it's not that big of a deal...

Thanks for having me as a member first, second I am the proud new owner of what I think is a grand prix ,in terrible condition, by doing some research I found this site, and have some questions, the rear hub, rim,tire, axle, etc is missing, my main concern is if most of these parts are standard...

My new favorite arrived today. Late 1967 or early 1968 I've been told. Did a light cleaning, assembled it, put on all new chains, a new throttle, some fresh gas/oil, it fired right up and ran like a banshee for all of 2 minutes, then stalled. Re-started, runs a bit, then stalls again. The two...

So, we have a 98 jeep grand cherokee, with a 96 engine. We had some problems after we swapped the engine, it wouldnt run properly sputtering/backfiring/stalling out/ragged idle. Weve replaced various sensors to try to fix the problem, bit it still persists! :hammer: It start up fine, idle just...

Wanting set 2 piece handlebars, Grand Prix, Scat Cat so on. Like in pic's There 4 the early standard model grand prix....

I've talked with a local business owner in Grand Rapids and he has okay'd the use of his parking lot for the use of having a minibike swap meet / sale. Only enough room for about 15 vendors, but that should be plenty.... for now. Cost would be $10 per 8x12 space. Anybody in the West...

Hey everyone.. Just thought I would share some photos of the new project I just finished.. A member in another post of mine sparked my interest in this add-on lighting alternator that was available for Tecumseh engines years back.. Well I was lucky enough to find a few NOS kits, and I snagged...

I have a Rupp Grand Prix. With the help of this forum it is believed to be a 1965. With 5" turbines on the corners which I believe to be correct. What size tires would be era approiate? I assume they would be square corner slicks but unsure of the actual tire size. Any help is as always...

I started with this. Then,a trip to the hardware store for spray paint,tape,a few nuts and bolts,and some spacers. One afternoon later: I'll use the 79cc Greyhound on there at first to test the durability of the pocket bike wheels. I added the plate to give it a club racer look to go with the...

Here is my Grand Prix Deluxe-I like the look of the pocket bike wheels. Perhaps my 79cc Greyhound 2.5 hp will do the job. I still haven't decided whether or not to repaint it-I probably won't.

OK...Like I said earlier, I have too many projects. This (I was told) is a CAT 350SS sold by JCP under the name of Grand Champion. I don't know if the 5HP engine is original,(might be) but it runs great. Needs throttle cable hooked up. Wheel inserts look great. Disc brake is original and works...

Spotted a go kart today on Craigslist. The listing said $50. Talked to the guy and he said the kart needed some work. Well I went anyway wasn't too far. The kart was a piece of junk but this one was leaned up against the garage outside. I asked if this one was for sale and he said sure...