h60

Is it possible to use a V60 blower housing and flywheel on an H60? both are early (around 1969-1970 engines) Thanks!

I dragged (another) old Ariens snowblower from the side of the road in nice shape, electric start, gas tank clean. It has a snapped rod. I knew this and hoped it didn't take out the piston, but it took some skirt off. The engine is H60 75003H 8163 Looks like the rod is 31380C Piston 33312B...

Model 75482S-2153D, paperwork included. Series 30 GTC driven unit. Both new. $465 shipped.

I'm about ready to rebuild a Tec engine, 6 Hp Engine H60 75414M SER 3269D. I installed a new carb kit, but engine still is hard to start, and bogs down under load. I've rebuilt top ends in 2 stroke engines (125cc and 400cc) but never rebuilt a small engine. Where/how is the best place to...

I picked up a 1988 H60 for next to nothing yesterday. Tore it down to assess the damage (a lot!). Will need to be bored and needs a new crank. Must be something about big blocks, because this is the second one I've picked up with the governor spool in pieces. Piston rod broken into little pieces...

Did you ever have one of those days where someone with a higher power was looking out for you? I did. I finally received my "new" H60 Tecumseh (the one I need a crankshaft for) this morning. I was anxious to get inside it and see what I had (and what I needed to find), so I tore into it. First...

Dr. Fruitloops just bought another H60, and it needs a standard length (2 1/4 or close) PTO. Let me know if you have one to spare. P/N Tecumseh 31827 or equivalent Thanks

i have a vintage 6 hp tecumseh h60 motor with lighting coil. perfect for your vintage mini bike project. 675$ buyer pays shipping I'm in northern california. i take paypal.

H60 parts for sale.....1974 Air Filter ( carb is no good) $15.00 Flywheel @ Magneto..good spark... $25.00 Muffler.... $10.00 Shroud. ..$15.00 Prices do not include shipping shipping from NJ, 08033 PAYPAL is preferred. [/URL] [/URL] [/URL] [/URL] [/URL] [/URL] [/URL]

How are Tecumseh valve seats removed? I'm building a hopped up H60 and want to put oversized valves in it. It seems that Tecumseh installed one insert for both intake and exhaust instead of one for each valve. Is the seat cast in or installed like a normal seat?

Trying to set up my big block throttle brackets and i notice this engines governor arm doesnt swing anywhere close to what it should in order to connect a throttle link. Below is the maximum in each direction. Is this just a case of removing the arm and reinstalling in a better position or is...

I have an used H60 Tag with factory rivets. Model-H60-75003F Serial 6173 04478 Could someone decifier this for me?. Thanks, Joe51

Looking for a Tecumseh H60 or H70 engine. (or any 6/7hp Tecumseh model variant) Needs 1" shaft, at least 2 3/4" inches long with 1/4 inch keyway. Any era, any condition as long as its complete or near complete. Going onto a early 60's Tote Gote Nova 670. Thanks

Tecumseh H60 6hp engine. 3/4" shaft. I do not know if it runs; it does spin freely. No fuel tank. Pretty sure it came off of a snowblower. Located in Rochester, NY $30 or best offer + shipping. Pics, click for larger version: Thanks

Stumbled upon this engine on Craigslist for just a few bucks and thought it would be pretty cool to put into my bonanza bc1000. Trouble is I don't know much about it, and don't want to try starting it without getting some recommendations from you guys on proper reconditioning so as to not ruin...

This part is so close to the hard to find 30199A I'm thinking its a good replacement. Its found all over the internets for two cylinder OV engines for controlling two carbs. Part #37400. Ima try one.

Hello, Just verifying Is the H60 connecting rod slightly longer or shorter than the H50 rod? I did not label when I disassembled a few of each. Thanks, Joe

First off I didn't paint the engine the crazy color blue. Bought off a member here.:scared: I was able to buy a h60 and stole the shroud off it because it had the throttle components that are extremely hard to find. My problem is my existing motor only has one governor arm and it's the one on...

Def needs rings at the least - smokes. Runs but rough. Repair or use parts to convert to elect start. 12 volt electric starter works. $85 firm + ship from 49279.

I'm getting a weak spark on an older Tec H60. Replaced points, condenser, coil, spark plug. Gaped points and plug. Was get no spark, but now getting a weak spark. How do I know if the flywheel magnets are weak, and /or need to be recharged ? How do the magnets get recharged ? Thank you for...