head

:blink: John Ashley Force Go Kart Signed | eBay

If you mill your head .030 to .080 would also want to shorten your pushrods the same amount to keep the valve train geometry in check. Or is this really a big deal cause you can adjust lash to correct the amount removed from head surface. just a thought i had . Anyone know or comment ?

Hi folks, I have what I believe to be a 69 fox trail tramp. It has chrome tank, fenders, bars, cage, head light and rear rack. Front and rear disc brakes. 4 hp tecumseh engine. It looks to be all original and in working condition. Even the tires say fox on them! I have put a new...

Hi guys. Not completely sure if this is a minibike, I posted pictures a while back of this contraption I built out of a Chinese scooter. It had a 33cc 2-stroke engine, and hadn't run for a while. I was messing around with the motor about a week ago, and got it to run for a bit, then stripped out...

I'm looking to buy (1) set of Carlisle double Indian head 4.10/3.50-6 knobby tires ,also looking to buy (1) set of Carlisle double Indian head 4.10/3.50-6 Universal Tread tire

Hey guys new here. I'm in the process of putting an engine together using the OldMiniBikes stage 4 kit. Everything is going fine until I went to put the head together provided in the kit. The valves from my existing head are loose in the OldMiniBikes provided head. I plan to call OldMiniBikes tomorrow and see what my...

How do I install this puppy? Carb came with some screws / bolts... Washers... Can,any one give me some kind,of guide to installing carb on the head. I have everything I would need to install Your advice is appreciated I'll post some,pictures if I can

I recently purchased a B&S 5hp flat head and it came with a different carb setup. I would like to replace it with the stock setup that has the fuel tank under it. I have searched and searched with nothing found. There were a few on eBay and they looked as if they were sitting in salt water for...

Anyone have an extra head around that's not butchered up too bad? Some milling OK if its done right. I'd like one to play with while leaving mine as is. Prefer OEM honda. Thanks. Greg

Briggs Raptor 3 tab head, Sandblasted no cracks, Brand new Raptor connecting rod with bolts, New Briggs Gasket, and a NGK commercial grade J19LM spark plug, $45 shipped, U.S. 48. Add another $5 ($50), and I will toss in the raptor cam, (not shown), in Very good condition.

Looking for a set of dbl Indian head tires 410/350/6 anyone get a set for sale thanks my number is 407-393-8835 or pm me thanks..

Just checking with you guys before I order my parts ROD - Im using the stock piston, what size rod should I get VALVES - will the NR stainless 27mm/25mm valves fit in the stock head seats PUSH RODS - is 5.440 the correct length for use with stock rockers Any help will be appreciated

Hsk60 tecumseh. It's a complete snow king engine with the 120vlt electric start. I will part it out or sell whole. It did run. Made some noise on acceleration. I removed the head and other parts. It is a long block at this point. Had never had the carbon cleaned from the piston. Basically the...

Not sure when I will get to it but I couldn't pass it up. You know i have a soft spot for pacesetters. Not sure what my plans are...it's needs a head gasket...also all the governor linkages are gone...do they reproduce tbose?

Michigan craigslist isn't the only place you should be shaking your head, check this one out from Indianapolis. http:// http://indianapolis.craigslist.org/clt/4857237370.html

Do any of you guys play? And if so have you ever made you're own amp? I've had this idea ive been kicking around my head for amps and I have some questions. Here's my axes and amp

Like stated looking for a real honda 18cc head

Gone through completely with parts from Ron Kimble, not restored to 100% but it's damn nice. Tank is intact with no leaks, 10hp Tecumseh pull start only but starts easily. New upholstered seat over original foam with new underlayment on an ash plywood base and it's bolstered as the original was...

good used 14cc head . just needs a good cleaning . complete stock head $50.00 shipped i will throw in stock flat top piston (has 3 dings on the face but should be fine ) lifters,stock rod,push rods,stock cam if you want those aswell:thumbsup:

Needing to know how to identify the 140 head. This head is a very small chamber head 24x25 mm valves I think.