jackshaft

Bearkat twister single jackshaft, 12 inch wheels

Recently purchased a Fox Campus, planning on building it into a nice little trail bike to putt around the yard and fields on. Here's a short run down of what I'm thinking: - 10 inch dirt bike wheels - CVT to the jackshaft - New seat - Honda CFR50F front fork - 8 inch mini ape hanger handlebars...

Double jackshaft twister with 12" wheels

Twister 12" wheels single jackshaft

I'm not sure if someone already thought of this one, but I thought I might as well get a laugh out of it. I dreamt this up a few years ago. Hope this diagram makes sense: J P A T C O K ---~~~~~~~== Fourth...

I have 2 Trailhorse's one with a brand new 2 speed and one with the original 1970 2 speed and nether of them seem to shift. Not sure if the Rmp's or speed isn't getting up high enough to shift? Both have new predator engines. Any ideas. Thanks

I'm looking for a set for jackshaft plates if anyone has a spare set. Thanks

OK so I'm new to the jackshaft scene, it's a rupp contintal and it's missing the jackshaft and rear fender brackets I'm thinking about making the brackets but the Jackshaft ? .so can I get some sort of aftermarket one or does it have to be O.E. and if I can use an aftermarket one is there one...

Bought 2 speed jackshaft and clutch separately, both as NOS here on OldMiniBikes. Adjustable jackshaft kit bearings and collars all new from OldMiniBikes WHS. Asking $250 for all including USPS. Prefer PayPal as a gift. Packed and ready to go. Ask any questions and I'll do my best to answer. Please PM only, per...

When I got this, the jackshaft was gone and some doofus had replaced the motor and ran the chain from the motor sprocket back to the rear sprocket. I'm looking at the 5/8" #35 Jackshaft Kit, shown here: https://www.OldMiniBikes.com/jackshaft-kit-for-35-chain.html Anybody here know the OD of...

I have this new only mounted Coleman ct200u jackshaft setup. Plate, cover, tensioner, bearings , chain and shaft are new. Sprockets are used but in great shape as far as I can tell. I also have a brand new clutch not pictured. $85 shipped

Anyone know what the replacement bearings numbers would be for the Jackshaft assembly on an MB200 are? It shows them in the parts breakdown but does not list them as avialable, only the complete unit. Working on one of these for neighbor, I can see a shield has been compromised on a bearing on...

I have a factory jackshaft for the baja warrior. The jackshaft is complete with the idler pulley, gears and cover. It is complete, bolt on and your ready to go. The condition is like new with about an hour of use. $55 plus shipping. I also have a used stripped jackshaft perfect to modify...

I need a source for a type "C" sprocket with a 3/4'' bore. I can find all I want in a 5/8'' bore. All I can find in a 3/4'' bore are type "B" sprockets. I am sure they are available, I just cant find them... yet. Thanks for the help, Doug Edit; I need a 40/41 sprocket.

Two part question: Can the brass bushing on the jackshaft clutch be replaced, or should I just be looking for a new clutch? I ask because after putting this project back together, the clutch bell makes the same noise when freewheeling that it did when I was a kid (it sounds like it spins to the...

Like it says up there. $158 shipped

Have Paypal ready, also have lots of nice adult toys to trade. Thanks, Matt

Looking for a new jackshaft for my ct200u and it looks like the Baja mb200 jackshaft is the. Same. Can anyone confirm this. Thanks

Looking to see if anyone has a jackshaft set up that they removed and aren't using. I've had a ct200u I picked up cheap in the back of the garage, pulled it out today and the jackshaft is bent. If cash wasn't tight I'd buy the aftermarket one. Thanks guys.

Looking to see if anyone has a jackshaft set up that they removed and aren't using. I've had a ct200u I picked up cheap in the back of the garage, pulled it out today and the jackshaft is bent. If cash wasn't tight I'd buy the aftermarket one. Thanks guys.