line

The following pic shows a 3/8 offset between the center of the driven and the inside of the drivers stationary angled drive plate. Before I cut .550 out of my jackshaft mount ... is the 3/8" offset correct?

So I have been working on my bonanza with a 3.5hp tecumseh. I rebuilt most of the carb and gave it a good cleaning. It runs pretty good, But sometimes when i full throttle it has split seconds of hesitation. Like seconds where it loses power. during those times it can sometimes make a...

This is a photo of a bike with the same conversion - don't have a photo of the chain side of the bike. I have a SS300 that needed an engine....so the 3hp Predator seemed the logical choice, but the chain doesn't line up. It almost looks like I need add a jackshaft to make it work. The engine is...

Having trouble at the house with my email server, so I can't load the picture I took, but here's my question. My Baja MB165 frame rails aren't in line across the bottom. If I use a straight edge along the bottom on the motor mount area of the frame, the rear rails where the axle is attached...

History: Barn find early 70's Arctic Cat Whisker with Sach's engine. Was able to clean her up enough and did 2 laps with it then it stopped running. Pulled engine off minibike opened her up on my workbench cylinder head damage cracked ring. Was able to source new cylinder head with rings but now...

it is my intent to design a mini that will serve as a work horse I have made a 3 wheeled mini by adding 2 large trencher tires on either side of a heathkit Boonie bike but we all know the problems with trikes and uneven ground it will point you down hill in a hurry. then I saw rokons these...

Can anyone identify this mini bike from these pics? Found it for sale and the price is right. Thanks for the help

Another novice question for those with on-engine vertical seam tanks. Engine originally had horizontal-seam, plastic tank with outlet nipple in the center/bottom of tank. No problem with fuel line radius out of the tank into the shroud. I now have reinforced rubber fuel line installed and...

https://www.youtube.com/watch?v=-ku2EDWFSpQ

lost the rubber tube can i use some fuel line or will it melt

Its a two stoke and the engine is not from this bike. Its a KT43 kawasaki 110cc that I got from CL. I cant get it to run without starting fluid. It has fresh gas and fresh 2 stroke oil mixed in. Brand new spark plug. I know its not getting fuel and I have the gas line valve open when Im trying...

I dont see a spot for non mini bike stuff for sale..I have a onan generator for sale...is there a place to post it?? if Im out of line asking on here please just delete and let me know and it wont happen again...thanks

I have a 70 RUpp Roadster and I am gong to replace the fuel line and put in a filter . Does anyone know what size fuel line it should have 1/4 or 1/8

stuff to add .. fuel line,fuel pump, top plate assembly for both throttle and fuel pump Question... Can I place a T in between the new fuel line of the stock breather hole in the valve cover & new line & a catch can ?

I recently purchased the Tecumseh carb for my HM80 and it has a hose nipple besides the fuel line nipple. Can someone tell me what it's for? I have determined the nylon fitting is for the fuel line. I don't know what the aluminum fitting is for.

Hey everyone, hoping someone else has done this and knows the answer. I have the hydraulic brake setup from hot rod mini bikes on the DB30 trike I just built. It fits with the included brake line but I had to run it in a way I really don't like the look of. I can get a replacement line in...

The kids want to put one of their 6.5 predator engines on the manco kart but the pto is not long enough so the sprockets can line up. I was looking at one of the pmr adjustable motor mount kit. which holes line up with the engine or the factory mounting plate. I can see how this would work on a...

Okay, so I've had this Raptor sitting on the workbench for a couple years. I bought an old Kart off of a buddy that had stopped racing, and he sold me his kart, motor, and a boat load of tires and wheels for $300. I didn't do anything with it when I got it because I've always played with the...

Found this on Raseseng website "WE WILL NO LONGER BE MANUFACTURING THE RACESENG KARTING PRODUCT LINE. WE ARE GOING TO FOCUS OUR EFFORTS ON OUR AUTOMOTIVE PRODUCTS."

I cleaned the gas tank on my Predator 212 to get rid of the rust/scale. I think I need to replace the gas line fitting/strainer but I cannot find the part or where to order. I searched the forum, but may be using the wrong terms. This is the fitting that screws into the bottom of the tank...