motor

Hi, I have the original doodlebug frame with a New 6.5 Predator motor in it. The motor has about 3 hours just changed the oil. I recently bought the bike with the motor swapped and the guy told me the motor shakes because the chain needed to be tightened which I doubt is true. It's fine up...

First off, new to the forums. Not much of a biker but with all the info I've been reading on these motors, this seemed fitting. Here is the deal. I recently purchased a 212 Predator and installed it on a Mud Motor kit I built. I'm currently getting great results with this factory setup...

Vintage Jacobsen 321 Engine. Barn fresh! The 2 cycle engine is in good used condition. The engine has compression but is otherwise untested. A must have for the antique engine collector as well as the mini bike or go cart enthusiast! $85.00 Pick up ONLY! Located near...

Hey Folk's, Just saw this Power Bee motor for sale on Charlotte's craigslist. https://charlotte.craigslist.org/for/5252490750.html Enjoy !

when buying a jet kit for a stock clone carb and it comes with a .36 and .37 jet and a emulsion tube. what is the big differents in the stock emuslsion tube from the one that comes with the jet kit.

Hello All, I have been lurking around for a while now and finally registered just a short time ago. My screen name comes from my favorite mini bike that I had as a kid, I have included a picture of me taken in front of my grandfather's house in 1975. He was a big inspiration for me...

I just finished installing a harbor freight predator motor in my Rupp Blackwidow. I saw a few people with pictures of it done on here, and ive seen a couple people asking about it, but didn't see anyone actually talking about what it takes. Its pretty simple so I thought I would go ahead and...

Guys, Here is a NIB Azuza complete 8" kit with everything needed to complete the build. I just don't have the time to build it. Azuza 8" Minibike kit with fenders, wheels, tires, chain, sprockets, kickstand, kill switch, all hardware included. Comet Tav2 Torque Converter. Dupor racing...

I've tried looking around for awhile now and can't seem to find basic information on the 212 Hemi. I bought a motor off the shelf at HF and it turned out to be a hemi model. I am doing a boat motor build and I just want the thing not to blow up ungoverned. Not really looking to burn the thing...

I have a old Thunderbolt mini muddier and I'm needing a carb for it. Can't find any numbers on the motor. How do I figure how what motor I have? Thanks

Well I'm still having problems with my Honda GC160 engine which was stored upside down on accident. Oil and gas the all over the engine, but it cleaned a good portion of it off and filled it up completely with oil and gas. Started and ran for 30 seconds while burning some oil and shut up when I...

got this tonight any brand ideas? 5 hp Honda wondering if the crank shaft is long enough to use a clutch

Need some help on this motor.Just picked up a taco 22 Frame Serial # 7P1852 The guy that owned it has had it over 40 years he said this engine has always been on it. I need some info on the Engine Craftsman Serial# 7179 02170 Model 143 571052 I cant get pics to load

Well the engine was hydro-locked with oil and I got all of it out finally. I put a new spark plug in since the other one was foul and it's not starting up. I filled it full with new oil and some gas but nothing. It still it's compression, but it has no attempt of turning over to start. At this...

Well my one Honda engine was accidently stored upside down and all the gas and oil leaked out. I turned it back up right and cleaned it off as well as I could. I threw some fresh gas and oil in and but the pull start is like stuck cause it only pulls half way. I thought it was because I had no...

I have a briggs WF with a tm28 and no matter what i do I cant get it to run right. It is good up to 1/4 throttle and then it boggs down to the point of dying if I hold beyond that too long. It is always rich, any help is appreciated. As of now I have put everything in the carb back to...

both engines are seized up. My boy wants to part these both out to help fund torque converters. everything off the engines including gas tanks lighting coil and flywheels minus both recoil starters. All reasonable offers accepted

isky mamba cam brand new gx200/160 , clone or hemi . no comp release $50 shipped predator rtc-2 head used but very good cond. $35 shipped hemi flat top piston b/n take off with wrist pin and rings $30 shipped brand new dual pipe header predator , honda , clone $55 shipped

Just curious if anyone is going (or already there). I spoke to smallbikes88 and he's already there. I'm planning on going down on Thursday morning early. But being the first time, what should I expect as far as entry fee, parking, riding minibikes, etc?? Thanks!! 43rd Annual Vintage Motor Club...

I'm looking for a new or slightly used late model Tecumseh 5 or 6hp motor.