neck

#S10198 SPEEDWAY FORK NECK BUSHINGS 5/8" ID. 1-3/8" OD. 1970-71 ALL & 1972 SABRE. REPRO. PAIR $15.00 Oak Grove MN.

Making neck tube out of thick wall steel tubing.

Happy Birthday. Hope your having a great day.:happybday::happybday::happybday:

The neck on this bike is pretty sloppy, there aren't any bushings or bearings on this brand of minibike from the factory?Maybe I could slip on a sleeve or race of some kind. Or even a bearing that slips over the ends of the neck? Any ideas?

Someone wanted to buy my gilson frame ( can't remember who now) then someone just wanted to buy the bushings so I decided to have a few sets of reproduction bushings made. I have one set left, they cost me $20 to have made. I'm asking $28 shipped for the set. I'm not trying to get rich just...

Who carries the replacement bearing for the manco big cat minibikes? Thanks for your help.

Does anybody have a good photo of the lil indian neck area? I'm try to see how that goes with the spring. Can't remember if washers go on top and bottom of spring. Thank you

Looks like someone's having a Birthday today ! :happybday: Hope you have a good one ! :happybday:

I'm looking for a gas tank for a predator 212 with the filler neck on the right side as the gas cap doesn't clear the frame on my nova mini bike...

3 Mini Bike Frames Three frames, $150... but I have no way of knowing if there's anything here that's worth my driving time? Anyone recognize anything here that's worthy of saving?

I'm trying to remove neck bushings from an Bonanza BC frame. I thought I could tap,tap,tap from opposite end with a long screwdriver and get them out. No dice. :hammer: Even tried a few whacks. Tried propane torch heat on the neck, along with whack,whack, whack :hammer:. That was probably...

I need a set of neck bearings for a Baja MB165 Heat/Warrior. Also need a clutch cover.

I am just about to paint my hodaka BC 1300sh project. Only problem is that I can't get the old neck bushings out. I have already ruined good parts because I didn't know what I was doing. I don't want to mess up the frame. Any suggestions? Thanks in advance!!! Derek

Happy Birthday Cliff!! Glad to have you back!! https://www.youtube.com/watch?v=S6M7i2mfMlU https://www.youtube.com/watch?v=DtjCXPxhMuc

I ordered all 3 sizes of the brass flanged bushings from OldMiniBikes warehouse for the neck of my 1966 Lil Indian 400. The only one that will fit in the fork neck won't accomodate the size of the bolt. Is there a special size bushing? 1/2" x 5/8" Bronze Bushing,5/8" x 3/4" Bronze Bushing, and the5/8"...

I've seen a bunch of roper builds on here and was wondering where you guys got the bushings for the forks and neck tube. I believe they are 3/4" by 5/8".

Good day everyone, A couple questions in regards to the steering neck of the forks with the spring under the neck itself, not sure how to describe it better than that. Are these strictly used for bushing type necks or can they be used for bearing necks as well. If used with bearings will...

I just picked this up the other day. The Suzuki tags on the side are screwed in. I have looked through all the pictures I can find and have not found this one. Very well-built, very solid frame, has a grease Zirt on the neck. I'm positive the wheels are incorrect. i'm also wondering what size...

Hey yall!! finally decided to get something going after sittin around for a bit... I picked up this George Barris bike in midwest pa a few weeks ago and it was trashed.. anyways after some cleaning i got most of the gunk and grime off of it. I picked up a 212 Predator Clone at HF and took all...

O.k. I have seen several bikes where there is play in the handle bars where the bolt goes through the fork neck mounting plates. I was wondering the best way to get it more snug. Do you just add some weld around the hole where the bolt goes through and then file down so the bolt fits snug? Or...