spacer

Does anyone know if the Briggs animal carb spacer /intake manifold will bolt up to a subaru ex21? Or could someone with an animal please give me the measurements center to center of the bolt/stud spacing on the head? Thanks

I want a couple of engine spacers 3/4" to 1" preferably aluminum to ease the installation of a predator in my Ropers, I know I have to move the slots forward but I want the engine's higher to clear the carb bowl. So if anyone knows where to find them or would be willing to make a couple for a...

Hi everyone, I'm relatively new to the forum so I hope I'm in the right spot. I'm trying to mount a non standard engine to an AZUSA minibike kit (Sachs KM 48). When I place my engine on the mounting plate, I have to shift it all the way to the right in order to line up the clutch and the...

Does anyone know the correct length for the 4 spacers on a rear wheel? The 4" steel wheel to be exact.

Is it necessary to use a spacer with a Predator clutch setup? I've seen it used on occasion and was wondering if it's really needed, or is it taken care of between the key way, set screws, and crank bolt? Thank you.

Does anyone know the size of the two spacers used on the rear wheel? I figured I would make them myself but im having a hard time finding their size. Mainly the length. Any help would be appreciated. Thanks!

I have an original restored TC-1 driver and HS40 engine for a 1971 Roadster 2. I noted that there is a spacer between the engine seal and inner disk. I have all the other components. Can anyone tell me the thickness and OD of the spacer for a TC-1 that goes between the side cover/seal and the...

Have a friend who picked up a MBX10 last week the rear wheel is missing the axel, bearings and all 3 spacers. Can anyone tell me the spacer spec so he can cut some up?

Looking for sprocket spacer and sprocket for 6" Manco wheel. If possible please include hardware for it too. Not to worried about hardware.

wanted......air filter spacer for a briggs 5hp, anyone have a used one laying around??? .....

manco wheel spacer in good conditon. $25 ship to your door. lower 48 states only. paypal/money or if you have a pigeon that can send cash. PLEASE PM ME ONLY THANKS

really nice manco wheel with spacer decent kenda tire comes for the ride :thumbsup: $45 shipped

Does anyone know if they make a 1" wheel spacer for a 6" Tri Star wheel?:confused:

Does anyone have or know of a 1/2" or 1" spacer for a 6" Tri Star wheel? Seen them for 5". Any info would be appreciated.

I have a 79cc Predator (this is going on a bicycle), and I want to use a 19mm mikuni carb. I have the carb and a manifold, but the manifold is too wide at the intake end (either end, actually but different bolt patterns on the carb end), to fit flush against the intake port due to the fact that...

The black plastic spacer between the head and carb somehow cracked on me, do I need this piece ? Can I just not use it ? Or where can I get a new one .. Predator 212

The engine wont run off choke. Cleaned the carb tried putting the muffler back on for less air flow. Could Ive damaged the black spacer some how thanks.

Im looking to install my 212 and need some help. I read the post on the clutch brake and will be doing one with my own bracket and cover. I need to know what clutch should i get and why. Also do i need a spacer kit? I've seen clutches on ebay for 23.99, Max torque for around 33. and halliards...

Shipping not included in prices in case you want more than one item, all came off a Butcher bird that was butchered :laugh: Wheel #1 (bearing and spacer included, OG hardware) $20 wheel #2 (bearing and spacer included, OG hardware) $20 Sprocket $18...

I am looking for the spacer between the rim and sprocket for my arctic cat climber. Let me know what you have.